This blog documents my experiences with powered paragliding since 2005. I started it as a training tool for myself and to share photos with my friends and fellow pilots The bulk of the material is strait forward flight log entries but occasionally I got inspired and expand on the experience.
This Report was compiled from information gleaned from sheriff reports and interviews of eyewitnesses. It also contains information received from pilots who knew and flew with Tony.
PPG accident 18 May 2019 Arcadia, FL
This was 61 year old Tony Littell who passed away in a PPG accident on the 18th morning of May 2019. Tony received initial instruction from USPPA instructor Joe Onofrio between July – September 2016. Tony was signed off to take the USPPA written test though never did. A few weeks later Joe and Tony met. Joe discovered that Tony had been flying on his own. Tony decided not to continue with USPPA training, Instead he self trained.
Bob Harrison a local PPG pilot collected information from another PPG pilot, who arrived minutes after the accident. The other PPG pilot also flew that day in the same area without knowledge of Tony’s flight. He new of but had never flown with Tony. Bob had also collected information from a non-PPG pilot who was an eyewitness to the accident and first on scene.
This is what I assume:
Tony was flying straight and level between 200-300 feet AGL when the left side of the paraglider let go completely. This initiated a high speed vertical descent as noted in the picture showing heavy left side impact damage compared to minimal damage on the right. This supports a rapid descent corroborating the left side of the paraglider released.
I believe the power lines were missed. With only a few seconds before ground impact, Tony removed his reserve and started a toss. You can identify and see in the picture the reserve separate from the paraglider. The PPG pilot that arrived on scene minutes after the accident mentioned the reserve container was about twenty feet away from the paramotor.
I receive a comment from a USPPA instructor who flies a similar unit. He mentioned to Tony over a year ago that the risers were showing excessive wear and should be replaced. He also thought there might be a burr on the CG ring. Another USPPA instructor who flies a similar unit says he found no wear after checking four other wings that had been flown extensively with his unit. Therefore we believe the area causing abrasion had been repaired. It was also known that Tony learned to weld and his machine needed a few repairs since he began flying. Tony had recently ordered new risers which had not been received prior to the incident.
The equipment was impounded by the local Sheriff department and the FAA was contacted for inspection. The FAA said they were not sending anyone to inspect. Instead requesting specific photos to be taken. The sheriff department would not let anyone other than family retrieve or view the equipment. The photos were given only to the FAA and an NTSB Safety Investigator. They were asked and refused to view or share the accident photos. Visual inspection is the best method.
We made contact with the family the day of or after the accident and initially given hope to a visual inspection which turned into a delay which turned into a refusal within a weeks time.
Unfortunately the cause of this accident cannot be determined conclusively because the equipment was impounded and destroyed without a visual inspection, at the insistence of the family. I feel confident if the unit is maintained in its purchased configuration it is a safe PPG.
I was right. Fly once a month and every flight is a refresher course. This morning the air was butter. The launch was clean and the flight was fun. I worked on trimming out the torque and did some lazy wing overs. The only turbulence I encountered was above 2800ft and again below 200ft where it was cooking off pretty good.
After the flight I spent a good amount of time with post flight. Everything looked good except the reserve bridle needed to be cleaned up. I like the new routing. God forbid I ever need to toss the rags but if I do, I think it will fly clean.
Couldn’t leave the house till 6:30 when Dawn’s alarm went off. At Placida Meadows it was light out of the east.
I set up very deliberately and then, aborted in a most clumsy manner, when I realized that I was wearing my straw cowboy hat instead of my helmet. For just a moment, after I’d pulled the trigger. I considered the odds of letting go the brake and tossing the hat to the side before committing to take off and it might have worked, considering the gentle way the wing kind of hovered overhead after I killed the engine.Oh well… I reset the wing and stumbled into the sky with the glider swinging right and left. It wasn’t pretty but I’d broken the fast.
The motor ran fine. I climbed above a large group of egrets resting in a swampy pond and dove down on them with the sun at my back. They all launched together and immediately split into three parts, left, right and beneath me. As I flew between them they swung around and returned to their spot on the pond. The air was already beginning to lose stability. It was bumpy from the surface to 250 feet and again at 900 feet. At 1200 ft. the onshore breeze was increasing and I could see an army of low puffy cumulus marching inland. The air was calm at Gasparilla Marina but it was beginning to stir up the water on the lee side of Gasparilla Island. After 20 minutes I returned to the truck and landed without drama.
I’m going to have to make an effort to get out more often. Once a month might be enough to keep my skills current but on the ground and in the air I felt anything but sharp. I was tentative on the brakes and to stiff in the saddle. Maybe tomorrow I can get back out and work on the basics.
Both of these were really non flights or aborted flights.
Last week I replaced my gas tank and even though I did a test run and thought everything was good, it was not!
I met Alvaro at the field at 7. There was a small storm to the west so we chatted and waited for it to move on. When the air was clear, we set up. Alvaro got right off and I set up east of him to launch from the street.
The takeoff was fine but at 50 feet just as I was applying power to climb out, the motor started to stutter like it wasn’t getting gas. Luckily I was able to set down at the end of the road. Then I set up again, making sure to run the motor for awhile to check for air bubbles or whatever was causing the problem. It was all good but again at 50 feet, it lost power causing me to set back down. Fuel is flowing and I don’t see any bubbles. Paul said that he heard the motor issues after my angle of attack changed with the front wheel much higher than the back. It’s a mystery I’m going to have to figure out.
This is the first engine issue I’ve had with the Generac after several hundred hours.