I recently got well enough to proceed with a Pinin project car nearing completion... apart from a persistent P0141 DTC, 02 heater circuit bank 1 sensor 2. It had no downstream sensor fitted when i bought it so only showed a code on cold starts, no mil light on warm starts. After twice being sent incorrect 02 sensors from ebay with incorrect plugs (maybe for the front sensor) I finally got one specifically for the rear downstream from aliexpress taking less than a week from china @ £14 and... 2.0 GDI Pinin P0141 heater circuit bank 1 sensor 2 resistor 'fix ..read more

Hi everyone, I need some help finding a throttle body assembly for my 2004 Mitsubishi Pajero 3.0L V6 (model number: V73WLRXVR, engine number: 6G72). My chassis number starts with JMYLRV73W4J0. Specifically, I'm looking for information on whether part number AC60-087 is compatible with my vehicle, which currently uses part number AC60-370. Part number AC60-087 is from a Delica space gear , engine number :6G72 , 3.0 L V6. Both parts match the same engine number and look similar but I am not... Parts Compatibility 2004 Mitsubishi Pajero 3.0L V6 ..read more

The car starts to shake in fourth and fifth gear when the rpm reaches approx. 2500 rpm. The revs do not increase and the vibration is noticeable. With the four-speed, the problem is approx. 100 km/h and with the overdrive gear approx. 120 km/h. The problem does not occur in 1-3 gears, the machine rotates well in neutral without problems. Where could you start looking for a fault? The trouble with this is that you cannot read the fault codes yourself. At least I haven't found a suitable App... Pajero mk3 (2004) 3.2 DiD vibration at approx. 2500 rpm ..read more

I'm looking for a scan tool for my Pajero Snow Athlete 1999 Japanese model V6 3500 A/T long wheel base V45W. None of the Mitsubishi diagnostic tools in South Africa can pick up my car because it's a Japanese import. My sensors have started acting strange after an altercation with a large pothole (a very common problem in South Africa) so definitely something happened to wiring somewhere but it doesn't help that none of the mechanics here have the right diagnostic tool to pick up my Japanese... Scan tool for Pajero Snow Athlete 1999 ..read more

i have a pajero mk2 2.5td 1999 , the engine died recently it started knocking bad and i have been considering swapping it to an om606 , there is one for sale with an om603 pump fully mechanical so no need for an ecu or any wiring the real question is would it fit in the engine bay ? has anyone done this and is it better to use the mercedes gearbox with the pajero's transfer case or go pajero gearbox ..read more

Hi everyone, I ran into a strange situation with my Pajero 2.5tdi from 1997. Yesterday I drove downhill and three lights show up together. The Fuel Filter, Battery and Oil lighted up. I contacted my garage and they cannot look into it until next week, so I looked around myself and tried to use some common sense. The internet isn't giving me any direct answers to the combination of the three lights, just the separate ones. So I did the following: 1) Checked the oil; nothing special... Mystery problem with three dashboard lights ..read more

Making this post because I have got a 6g72 crate engine that I dont have use for, if anyone is interested my email is ar611877@gmail. com ..read more

I have 1997 Mitsubishi challenger, my rear LTR/cigarette lighter power socket has blown fuse. Any information where fuse box is please? Under bonnet is fine, can't see fuse panel under steering wheel or beside accelerator pedal. Cheers ..read more

Why does the original equipment cable have THREE grounding locations? ? 1st to the body 2nd to the frame 3rd to the engine block ..read more

Folks, Request your assistance. Where does this bracket go? Rebuilding a 1995 Pajero 2.8L TD 4m40 engine and don't remember where what feels and looks to an aluminum bracket (pictured below) goes. Bracket is ~5 1/4 inches long on one side and ~4 1/2 inches on the other. Two holes on the long side are smooth (no threading) and go all the way through. The two threaded holes on the other side bottom out. One takes a 10mm bolt, the other an 8mm boll. Bolts shown in the pictures may or may... Where does this bracket go? 1995 Pajero 2.8L TD 4m40 ..read more