Hello, Continuing the discussion from my previous post here.  I wasn't able to make the suggested solution work. The mentioned CyU3PUsbAckSetup call i... Continuing the discussion from my previous post I wasn't able to make the suggested solution work. The mentioned CyU3PUsbAckSetup call is done before the data is read from the endpoint. At that stage, I don't know yet if I should issue an ACK or a STALL. However if I remove the ACK, the  DMA loop the follows times out. I would appreciate any further advice. Thank you ..read more

I need to create firmware for the CCG8 - CYPD8125, and was looking for any BSP / programming guide when using the modus toolbox. When using the Modus Toolbox and want to work with the CCG8, what setup do you recommend. I guess to start with a example for PMG1 - like  And guess we need to use the   though I don't see anything for CCG8. Do you have any plans to include more CCG8 software support in the Modus Toolbox software (E.g. BSP, Exaples, pdstack middleware) soon ..read more

Hello, I hardware using fx3, by the FPGA to provide the image, gpif configuration bit 32 bit, the resolution is 1920 * 1080, the frame rate is 30 when the image output is normal, when the frame rate is increased to 40 frames, the upper computer display black screen, we tried to reduce the resolution to 1280 * 720, the frame rate of 90, the image output is normal, when in the increase of the frame rate, the output of the black screen, we would like to ask Is the bandwidth limiting the frame rate? Our bandwidth should be enough, or other parameters limit the bandwidth, please give answer, thank ..read more

We are using the EZ-USB™ CX3 Denebola kit as a validation platform. We have learned that the EZ-USB™ CX3 Denebola kit supports USB3.0Vision via the web address below. We would like to get the source code for Cx3U3VOV5640.img for reference. Please help us. We have signed an NDA confidentiality agreement with Infineon.how to contact you to get the source code,please help us ..read more

Hello, I am working with an INFINEON - CY7C65631-56LTXI - Interface USB, EZ-USB HX2LP Lite™. I want to use a Cypress blaster to configure the EEPROM c... I am working with an INFINEON - -56LTXI - Interface USB, EZ-USB I want to use a Cypress blaster to configure the EEPROM connected to it. I searched on your forum and tried different version but i don't thing i have found the lastest one which can configure a CY7C65631/HX2LP. I also didn't found a right I tried to install its driver but i couldn't found a Can you share these different elements with me ? I'm working on Windows 11 but i can ..read more

I am developing an application using GPIF and the FX3 using the AN75779 example and it has code for detecting backflow with BACKFLOW_DETECT. It is my understanding that this is when there is an overwrite to one of the DMA buffers. We have taken care to ensure our 32KB FX3 buffers are being written to in 4 bursts of exactly 8KB from the FPGA but we are receiving these errors occasionally anyways. They do not occur all the time and get worse if the computer has more tasks active. We are using a Multi-DMA to send UVC data and seeing CYU3P_PIB_ERR_THR0_WR_OVERRUN and CYU3P_PIB_ERR_THR1_WR_OVERRUN ..read more

Hi, I am trying to configure a 1500x1500 sensor at 60fps. I have attached the image sensor configuration and receiver configuration. However, I am unable to generate any output. Both the CSI clock and Output pixel clock are showing errors. The CSI clock value is 960MHz, and therefore dividing it by 2 will yield 480MHz. Since the output for 24 bits needs to be in multiples of 24, I am fixing my camera pixels to 1512 x 1512. Kindly guide me on what should be done. Thank you ..read more

Hi!  We have a use-case where we need to update a CCG4 via the CC lane from another CCG4.  We have worked with sending and recieving custom VDM messag...  We have a use-case where we need to update a CCG4 via the CC lane from another CCG4.  We have worked with sending and recieving custom VDM messages between CCGx, both by HPI and via internal C APIs in the CCG4 firmware. We are today updating FW via I2C via HPI, but as mentioned, we also need to support it via CC. We noticed that in the Power SDK there is cc_src_bootloader project which is used by the main firmware there ..read more

The board is powered by a power supply, and according to the third connection method in the manual, GND VS LIN RST is connected, NAD is set, the connection configuration is as shown below, and the firmware is up-to-date, (before it could be connected normally, but then it suffered from a short-circuit, and the Dupont wire connecting VS was burnt, and after that it couldn't be connected any more), can it be considered that the uIO stick has been damaged ..read more

hi, i am an arch engineer from oem, and my company bought 2 TC4DX board, i need ads limited to  estimate this board, but i had already find it in the official website and asked my support for help, but i do not have a download link yet. is there anyone can help me ..read more