Canadian Hobby Metal Workers
43 FOLLOWERS
Canadian Hobby Metal Workers is a community to discuss all forms of metalworking, sourcing metals, all things pertaining to CNC machines and conversions, and more.
Canadian Hobby Metal Workers
5h ago
I have a 15 hp RPC that has run well for most of 20 years but has started acting up.
Initially I had a start cap blow up about three months ago while the RPC was running, then about two weeks ago, it blew again, this time on start up. I replaced it and thinking I had done something wrong, started it again and after it ran for 15 or 20 minutes there was a rattle of contacts an the 'on' light flickered.
I checked all the capacitors and even replaced the potential relay and it started but...
Read more ..read more
Canadian Hobby Metal Workers
6h ago
"Boxford lathe. Early 70's vintage. 4.5" swing. 20" between centers. Good condition. Comes with tooling shown. *No 4 jaw chuck.*
220, 3ph, 3/4 hp motor ..read more
Canadian Hobby Metal Workers
6h ago
Four or five yrs ago my ophthalmologist started to mention I would need a cataract operation in the future.
That condition progressed until last spring i notice a significant difference in sight quality and it continued to get worse over the summer. Mid summer I had to quit driving and using my shop equipment was almost impossible....I couldnt read the dials or see what the cutter was doing.
The surgeon was hesitant to do the surgery on me until it was absolutely necessary ( I...
Read more ..read more
Canadian Hobby Metal Workers
20h ago
Log into Facebook
Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com ..read more
Canadian Hobby Metal Workers
22h ago
This seems reasonable.
Metal Lathe with 1-1/2in Spindle Bore, PBR TM-175 | Power Tools | Calgary | Kijiji
For sale is a metal lathe that I have purchased at an auction in Brooks. I just need to the tool post and holders from the lathe. Comes with a steady rest. 48" between centers and 8" 3 jaw chuck. Pick up in Brooks by Friday June 07. Will meet buyer during load out. 575v 3 phase, requires a motor...
www.kijiji.ca ..read more
Canadian Hobby Metal Workers
22h ago
Craftex CX 601 Milling Machine w/DRO and Stand | Power Tools | Edmonton | Kijiji
CX 601 Milling machine with stand and DRO. Specifications: Motor: 1.5HP , 110-V, Single Phase Drilling Capacity: 32mm (1.25") End Mill Capacity: 20mm (0.78") Face Mill Capacity: 76mm (3") Spindle Taper: R8 Spindle Stroke: 70mm (2.7") Head Tilt: 45-degree to the Right & 45-degree to the Left...
www.kijiji.ca ..read more
Canadian Hobby Metal Workers
22h ago
Seems pricey.
Milling Machine 9x49 Knee Mill | Power Tools | Calgary | Kijiji
$9500 Flippers need not apply This mill is from Modern Tool in the mid or late 2000s. Second owner 9x49" table, good cond NMTB40 quill Power X,Y Variable speed headstock 230 volt single phase Home shop history, minimal use Residential shop, you will need a knuckle crane and be prepared to have...
www.kijiji.ca ..read more
Canadian Hobby Metal Workers
22h ago
12 inch Rotary Table | Other | Ottawa | Kijiji
Mecatecnica 12 inch rotary table Made in Spain Please reach out with any question
www.kijiji.ca ..read more
Canadian Hobby Metal Workers
22h ago
Gunsmithing tools | Other | Barrie | Kijiji
Brand new gunsmithing tools 1-winchoke reamer cutter 1-winchoke threader 1- 2-3/4 to 3” reamer for opening up the chamber from 2-3/4 to 3” for bigger shells 1-modified choke reamer 1-improved cylinder reamer $400 for everything firm I can ship for a fee
www.kijiji.ca ..read more
Canadian Hobby Metal Workers
22h ago
If @PaulL wasn't on his reclusive island shop this morning he likely would have heard the bands walking on the road behind his house. Oak Bay Tea Party Day ..read more