Revit Forum - Mechanical, Electrical & Plumbing Forum
151 FOLLOWERS
Get help and support with Revit Mechanical, Electrical, and Plumbing. An independent and non-profit discussion group, for everyone passionate about Autodesk Revit.
Revit Forum - Mechanical, Electrical & Plumbing Forum
2w ago
Advice please?
We use Navisworks to review MEP services internally (as its easier to 'fly' through than in Revit).
I have set material/colours to pipes and ducts for each service as Navisworks uses this in its export.
Is there a way that the same principle can be applied to Containment so I can apply a colour depending on the service its used for (Fire, LV Power etc)? Or is there an alternative family that i can use where you can apply a material to?
Any advice would be appreciated ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
3w ago
Hi,
Is there a way to modify how Revit is showing calculation points from ElumTools? In attached file you can see that the points are very dense. When I print the whole level the image will be blurred.
I don't want to reduce the the calculation points in "Edit Points", I'm looking for a solution to not show all points when I press "View/Hide Results ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
1M ago
To be specific I have all these queries in my mind
- How to manage ongoing coordination efforts throughout the design process using Revit?
-What best practices exist for collaborating with other disciplines (architectural and structural) to ensure a clash-free design?
-Are there any Revit add-ins or extensions that can enhance MEP coordination and clash detection workflows ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
1M ago
Revit Users,
I was trying to figure out if you can put in a pre-adjusted height in the crop box for a SECTION VIEW? Every time I run the command for this particular job that has a few floors the section box is populated with similar to a 20 floor crop region. I can just adjust, but if there is a way to populate a smaller crop region that would save me a little time. Any kind of feed back would be a big help and greatly appreciated. My end goal is to adjust the height of a section view without it populating a high crop region that I have to adjust quite a bit.
Thanks ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
1M ago
I very green on Revit.
I am doing final labeling of pipework on a pump station - there are 3 phases to the project.
I need to indicate where the limit of construction on the first phase is.
What is the best way to indicate limit of construction? I would prefer to show it with a label and arrows - but not keen to use section for this ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
1M ago
Hi you guys.
I m working at fire detection family, but i can't do the same mask at the annotation i've done in the outlets family.
In the outlets family i used a region mask to hide my conduits that pass near the annotation, this way i can show my symbol just right in the floor plan sheet.
Outlet family (working proprely)
Link to the outlet (larger than 2mb) : https://we.tl/t-eQrzlKsGBe
But when i try the same method in my fire detection family it just don't show de symbol right.
Fire detection (with region mask, not showing the annotation)
If i don't use the mask it just show the condu ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
2M ago
I had a louver that was not showing properly in a section cut within a project, and I couldn't figure it out, so I downloaded another model from Greenheck. Ran into the same issue. Moved it to a new project with almost nothing in it and created sections (one section then another copied/pasted aligned same place & flipped) and had the same issue (pic 1). I figured I'd try changing the family category; the visibility was much better(pic 2).
Does this always happen with Air Terminals? Why? Can it be fixed?
pic1:
pic2:
original download ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
2M ago
I have having issue connecting pipe to fixtures,
the pipes are disappearing when i try to connect them and they are also not located in the 3d view
my view discipline is set to mechanical ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
3M ago
Hello. I am facing an issue with the piping systems and colors of pipe fittings, In Revit I have modeled my plumbing model and assigned piping systems to all pipes like sanitary, vent, storm etc. but after exporting to Navis I observed that the piping system and color of some pipe fittings changed. you can see in below images. 1st image is Revit and 2nd one is Navis image. In Revit for my sanitary pipe, I have sanitary pipe fitting with pink color. But in Navis works it changed to storm drainpipe fitting with brown color. I want to change this fitting as there are more numbers. is there any so ..read more
Revit Forum - Mechanical, Electrical & Plumbing Forum
3M ago
How to resolve this issue? Why calculated air supply do not show?
This is below drawings, I am learning revit basics please help me ..read more