Ok, so I've been primarily a HPe shop, I've currently got two - 3par arrays - 120 TB each mirroring each other. Run active stuff on both sides, metro storage cluster. In any case Looking into replacing the two arrays, they've performed well, only complaint is running out of space..LOL So basically a large chunk of stuff are images, pdf's. A lot of things that don't dedup/compress great. I've got development running against the arrays as well. I will say that we are budget conscious, so I'm looking for a compelling reason to get purestorage over a HPe Primera.. I'm assuming Primera will come ba ..read more

Hello community.  Is there a way to create a bootable USB or DVD/ISO from the boot partition (C:) of a functioning Windows Server 2016 running on a DL380 Gen10 with RAID configuration?  I need to boot from a source that has all the HPE drivers loaded so that I can access the C: and (OS and data) partitions of an existing RAID array.  Booting off a Windows Server 2016 installation ISO does not help because it does not load RAID drivers, therefore the C: and drives are not visible.  Thank you ..read more

Hi peeps, I have about 320x DL360 Gen10 servers, and about 160x ML30  Gen10 servers spread across 114,000sqkm, all managed with OneView 8.60.01. We need to identify which of these servers have MicroSDUSB kits in them, ideally with a summary report, so we can have them removed on the next on site visit - powershell seems the most logical here. Does anyone know how I might setup a script to identify which servers have these MicroSD USB kits in them? I found a the OneView PS module, but it does not even show the SATA drives connected to the server ..read more

I have a Cisco ASR 1001-x router with a 10g interface that I want to connect to a separate switch (HP5700) and this separate switch will be connected to a native vlan1 on a HP switching fabric (5700's 8 switches) for databases (inside for ASA), now I want to create a sub interface on that same 10g interface to another set of switches that are also on a separate switch fabric (4 switches app/web servers "dmz" on ASA). Currently inside network and DMZ only talk to each only thru ASA. Since both sets of switches (inside and dmz stacks) are vlan1, how would I do this? The other side of ASR goes to ..read more

Hi there, I have a DL380p Gen8 and it was working perfectly fine, until one reboot. It just didn't boot up anymore. Now the red status light in the front is blinking, which led me to think that the power supply could be dead, but replacement also sadly didn't help out. It does try to boot, but before the hard drives or the fans start spinning, it's also going into the orange sleep mode again.   Also tried removing all the DIMMs except 1, also without any luck. Replug everything, also without any luck. What I found indeed is "PORT 84" LED 7 to be blinking statically. Maybe somebody here g ..read more

Hire The Best Certified Hacker For Crypto Recovery // Captain WebGenesis In the ever-evolving landscape of cryptocurrency, scams and fraud have become prevalent issues that often leave victims devastated and helpless. However, amidst these challenges, Captain WebGenesis emerges as a beacon of hope for those who have fallen victim to crypto scams. With its unparalleled expertise, efficiency, and commitment to justice, Captain WebGenesis stands out as the best company to recover crypto after a scam.  ..read more

Is it possible to get an HP-UX license for personal use? Commercial UNIXes are a bit of a mystery to me and I'd like to try it out ..read more

Hi all. I need help. FlexFabric 20/40 F8 module is connected to Cisco 9396PX with 40GbE QSFP-CR4 DAC cabels  VC Q1.1 port status is "Not Linked". From Cisco side also No Link I have two such modules, two cables, both are connected to Cisco and both have this status. I don't know what to do with me VC Side: ->show uplinkport enc0:1:Q1.1 ID : enc0:1:Q1.1 Enclosure : CZ3327J632 Status : Not Linked Type : QSFP+CR4 (external) Speed : Auto/Auto Used By : -- -- Label : Q1.1 PID LED State : off LAG ID : -- -- Connected From : -- -- Connected To : -- -- Paired With : -- -- Autonegotiate : Defa ..read more

Hi all. I need help. FlexFabric 20/40 F8 module is connected to Cisco 9396PX with 40GbE QSFP-CR4 DAC cabels  VC Q1.1 port status is "Not Linked". From Cisco side also No Link I have two such modules, two cables, both are connected to Cisco and both have this status. I don't know what to do with me VC Side: ->show uplinkport enc0:1:Q1.1 ID : enc0:1:Q1.1 Enclosure : CZ3327J632 Status : Not Linked Type : QSFP+CR4 (external) Speed : Auto/Auto Used By : -- -- Label : Q1.1 PID LED State : off LAG ID : -- -- Connected From : -- -- Connected To : -- -- Paired With : -- -- Autonegotiate : Defa ..read more

Greetings,   The Localhost node keeps giving me the "Incorrect iLO credentials" error. I have tried resetting the password and creating a new user but that does not seem to work. I am able to log in to the iLO portal with the password.   How do i fix this ..read more