1.6 16v VTI 120 hp, Temperature is on the gage is ~90c and does not creep up at idle, however, the fan does not come on and the A/C clutch does not engage. The fan and fuse are good, as I unplugged the coolant temperature sensor and the fan came on high. I have a new temperature switch and fan resistor on order but now I’m beginning to think it may just be the A/C is low on refrigerant and the fan has always just came on because the auto A/C kicks the compressor on even when using the heater ..read more

So my 2010 Peugeot 207 Sport VTi has been leaking for 6 months and despite two coolant system pressure tests two mechanics couldn't find it. After just opening the tank to do my usual refill. I noticed the leak (likely because its got worse like any leak may do). I have attached a picture. Its directly under my coolant tank where the hose connects to the tank. What should I do? the only related part I can find to buy is the actual hose. Is there a temporary solution till I get to a garage... Coolant leak from right under expansion chamber ..read more

For about the last week the fan on my 207cc (2008) has been humming louder than normal and as I was driving it yesterday it went in to limp mode, nothing came up on the centre console but after I pulled over for a bit it started up again and was fine. Any ideas what might be causing it ..read more

Hi folks. I've made my introduction and I have a question for the forum. I have bought this lovely car for my daughter and looking around it I find a media connector in the glove box. I can't imagine that this is a factory fitment so I'm wondering if anyone can identify a likely make? Where would it typically be connected? Also what is the round dial thing on the glove box wall? Is it just a vent to send heating/cooling air to the glovebox from the AC duct... 2008 Peugeot 207 media connector in glove box ..read more

Hi. So the engine light has come back on. The lambda sensor has been changed twice (still within waranty time frame) exhaust box has been changed, catalytic converter has been checked, no issues there. ECU has been checked no issues there. "Engine fault repair needed" flashes on the dash. The car loses slight power sometimes & sometimes for a split second when i turn the car on the steering wheel is stiff. O2 sensor has been changed to. Any help? Known issues. My mechanic is not a... 207 2011 engine light returns ..read more

Noise coming from engine bay, sounds like a blowing exhust by the manifold. However no leaks that i can see with heat sheid off. Silght puff of smoke possibly out of back of engine. Also engine pops & coughs. Very noisy on accselaration. Any thoughts ..read more

Hello. I have a problem with my Peugeot 207 1.6vti 120hp petrol, the engine has a power loss,it also has a shaking at idle.also the ckeck engine light is on,P1340 error. i want to mention that when i press the gas pedal i can hear a specific sound from the back seat,from the fuel tank,possible fuel pump? The spark plugs and ignition coils were changed.Thank you ..read more

So changed my spark plugs on my 1.6 petrol and one of them had oil on it which would explain the engine not starting, is it worth replacing the seals? It’s only done 74k ? What’s ur thoughts ..read more

Hi everyone. Recently bought a 207 cc (2010 1.6 vti) and very slight notchiness going into gear. Decided to 'bleed' the clutch slave cylinder as a starting point. According to my Haynes, all 207's have hydraulic clutch. Yesterday ripped out airbox, battery, resonator box, etc, etc to get to said slave cylinder. Darned if I can find it. Took loads of pix with flash on phone. uploaded to my comp and examined them carefully. There is definitely no slave cylinder that I can see. Is the Haynes... Hydraulic clutch ..read more

Hi, I want to know is it possible to remove the catalytic converter from my 207? Thanks ..read more