Hi Yuri, Could you kindly help to check whether we can use IPP to analysis hair growth on scalp? Normally we take two pics. one is x-2D means fresh shaved area, another one is Tx means 2days after shaving.  We wants: 1. length of each hair of shaved area (Tx-2D) 2. length of each hair of 2 days after shaved area (Tx) 3. each hair of the two picture need to be matched, so they can use length of hair after 2 days minus length of hair just shaved to see how long it grows. further to caluculate rate of Telogen hair. Telogen hair can be defined as grow less than 0.2mm of 2 ..read more

2024-04-30-163527 All -- I am working with an customer that has IP 10. They are collecting data from 3 REGIONS of IMAGES that are FRAMES in a MOVIE. I can set up the DATA COLLECTOR to capture the information they need. SUPER. Unfortunately the DATA is organized poorly for their application. They would like to see their 3 REGIONS as 3 COLUMNS of DATA rather than 3 ROWS of DATA. The SCREEN CAPTURE below and attached illustrates the CURRENT vs the DESIRED for a SINGLE IMAGE that illustrates the type of challenge faced here. Is there a way to configure the DATA COLLECTOR to report the mea ..read more

Hello everyone, In Image-Pro10.0.4 Build 6912, I am attempting to load a file directly to the "Global Recipe" as in the following post on this forum to automate smart segmentation.  https://forums.mediacy.com/discussion/comment/444#Comment_444 However in my case there is a need to change the input .isg file due to differences in the image sets examined (different lighting conditions, coloring, for instance). I could have users generate their own .isg file in the correct folder and rename it so the macro can find it, but I would prefer if I could use a dialog box to locate the file and ..read more

  Hi everyone, I have encountered a measurement requirement. I want to determine the extent of detection for the dense area on the right side. I want to obtain the measurement results of the thickness of high-density areas, as shown in the following image. I currently want to determine the level of density by counting the number of black-white transitions via [Line] to judge the degree of density. As shown in the following image How can I obtain the number of black-white transitions for each line segment, or is there a better method? Due to computer performance issues, I don't w ..read more

Other buttons work (e.g., Use 'Excel' button...); however, when I click on the disk to save in One Click nothing happens ..read more

I need to extract the outline coordinates of an object into a data table, but there are some limitations. First, using the polygon bounden points is not ideal because they are not regularly spaced which would make the outline analysis more difficult. I thought about extracting the radii measurement and using some basic trig to get the end points, but this would only give me 32 outline points and I may need more. Is it possible to change the radii measurement to adjust the number of measurements? Another way of doing this would be to extract a specified number of equidistant points around the ..read more

Hi, is there an event to recognize manual changes of measurements? Subsequently, a program code should be triggered. In detail, this would look as follows. There is only one measurement on the image. The user moves or changes the measurement. This trigger causes program code to be executed. Thank you very much. Best, Friedrich ..read more

Hallo, the function keys F10 (step over) and F11 (step into) are not working in debug mode. It works only when I push the button. However, F9 (set breakpoint) and F5 (Run) work. Do you have any ideas? Thanks Best, Friedrich ..read more

Hallo, I am looking for an easy way to convert ROIs in Measurements. Because I know there is a simple way to convert Measurements into ROIs. Like: <div>Private Sub ConvertMeasurementsToROIs()</div><div>&nbsp; &nbsp; &nbsp; &nbsp; Dim imageA as McImage=ThisApplication.ActiveImage</div><div>&nbsp; &nbsp; &nbsp; &nbsp; Dim md As Mediacy.Addins.Measurements.McMMData=imageA.MeasurementsData</div><div>&nbsp; &nbsp; &nbsp; &nbsp; If md.SubFeatures.Count=0 Then Exit Sub</div><br><div>&nb ..read more

Hi everyone, multi-channel (czi) images with 3 - 5 channels are used. The app activates a defined channel. Another function can be used to determine whether a measurement is present on the active channel. To do this, a measurement must be drawn in by the user with the measurement tools. This works correctly on some workstations and not at all on others.  Windows 10 Build 19045.3996 and Image Pro 10 Build 10.0.15.7533 are used on the workstations. Program code for activating a specific channel: Public Sub SetChannel() If ThisApplication.ActiveImage Is Nothing Then Exit Sub ..read more