TractorByNet Forums » Yanmar
3 FOLLOWERS
Discuss classic and grey market Yanmar tractors and equipment! Here you can share your Yanmar 3TNV76-Q injection pump question and find out how to add some stability to a small Yanmar tractor. Ask questions related to technical issues with the Yanmar tractors and get to know how to troubleshoot them.
TractorByNet Forums » Yanmar
1d ago
While I was replacing my axle seal on my F15D, the tiller sprung a leak.
I replaced seals on both sides, and both sides the seals were in horrible condition. They were shredded. The bearing on the right side was shot, too. I updated the bearing with an 2RS series to help prevent the elements from seeping in and ruining it again. This is more of me sharing but I was also curious if anyone has ever added a zerk fitting (grease fitting) to the cap piece (circled in yellow) as I could see it...
Read more ..read more
TractorByNet Forums » Yanmar
1d ago
This is a good picture of the 18HP 3 cylinder Yanmar 186D engine, model 3T72H, for comparison to the Grey Market Yanmars ..read more
TractorByNet Forums » Yanmar
1d ago
Where is the voltage regulator on a F20d. Diagram show one but i dont see one ..read more
TractorByNet Forums » Yanmar
1d ago
I have a Yanmar YM1500. Ordered new brakes and seals to deal with the oil leaking into the brake drums, now I'm ready to tackle the clutch issue.
The clutch doesn't fully disengage. I adjusted the pedal and there is still more adjustment to go, but when I push the clutch in it just keeps kissing the flywheel so getting into gear can grind unless I just jam it in quickly. If the transmission is in first gear and the clutch is in, when I take my foot off the brake the tractor wants to inch...
Read more ..read more
TractorByNet Forums » Yanmar
3d ago
I had my loader cylinders rebuit and I didn’t mark my hoses because i thought it would be easy to tell which hose went where, but now realize the hoses are not right. Is there a diagram that shows which hose goes to each port on the cylinders ..read more
TractorByNet Forums » Yanmar
6d ago
First time poster.
I have an F15D Forte with a RSA1201 auto tiller on it.
Currently, I'm in the process of changing my rear axle seal.
While in the process I thought I'd address my gauge wheel that isn't turning.
I started the disassembly process but I'm currently stuck at this point as the shaft won't come out. I'm assuming there is a clip behind the black plastic part but I wanted to check with others before I attempt remove it.
Has anyone changed their gauge wheel bearings before...
Read more ..read more
TractorByNet Forums » Yanmar
1w ago
The battery was stolen out of my Yanmar FX32 tractor. I called my local car parts store and they said they could get a battery that would fit in the space, but it's best to have the part number, to make sure I get the correct cranking amps. I don't have the receipt from when I bought that battery. What battery should I buy?
Thanks,
Peter ..read more
TractorByNet Forums » Yanmar
1w ago
I am having trouble Verifying the part number for a Yanmar GT14 diesel garden tractor. After about a half hour the dealer came up with 194215-52110. He couldn't verify that it had the counterclockwise rotation to warm the glow plugs and I'm having trouble verifying it anywhere online. Can anyone help me with this? Also, this part number works for many makes and models ..read more
TractorByNet Forums » Yanmar
1w ago
Would anyone who has a Yanmar emblem (like the one pictured below) be willing to loan it to me so that I can make a mold or be willing to make a mold to send me? Making a mold of it in plaster of paris should be easy. The mold could be filled with a plastic, then the plastic emblem painted with Yanmar colors and VOILA! a new Yanmar emblem! Anyone willing to do that ..read more