Cruzbike Forum
1 FOLLOWERS
The Cruzbike Forum is the best platform to discuss recumbent bikes made by Cruzbikes. Talk about the different kinds of Cruzbikes manufactured and discuss the bikes made for speed. Share information on indoor racing and training and talk about your Cruzbike adventures. Get to know about Cruzbike classes to help refine your recumbent bike riding and techniques. You can also discuss the bike..
Cruzbike Forum
22h ago
2021 S40, Fewer than 200 miles, Scratch free, Additional slider, Cateye Padrone, $3500, Boulder, Co ..read more
Cruzbike Forum
22h ago
Selling my Quest 2.0, which I bought new from Cruzbike in May 2014.
Basically only the seat and cushion, frame, crankset, brakes, and stem riser are original. You can read my upgrade thread Quest 451 to 507 here on the forums for details on most of the changes. You're welcome to PM me with questions.
There's a small scrape on the fork, a few tiny paint chips on the rear stay, and a bit of paint rubbed off the head tube by the brake and shift cables. Has not been crashed.
The Quest...
Read more ..read more
Cruzbike Forum
2d ago
Ok all - I go over this in all of the assembly videos but it seems to me missed way too often:
Please DO NOT OVERTIGHTEN your chain stay clamps. Every time I see a broken one it is the same pic - the surfaces are mated completely against one another - that is TOO tight and if you do this - they WILL break.
I am posting this because currently we are OUT of spare chain stay clamps. More will be coming - but if you want to be riding this summer - DO NOT OVERTIGHTEN these clamps.
Maria, Jim...
Read more ..read more
Cruzbike Forum
5d ago
Upgrading to SRAM Apex 1x11, installed GXP BB fine, but when I install the SRAM apex crank and attach the non-drive side crank arm, the whole crank gets tight and stops freely spinning.
The GXP comes with 2 spacers that i've put on each side of the BB, per the install manual. Is there some eccentricity I'm missing here or something silly?
GXP Bottom Bracket - BB-GXP-A1 - SRAM
GXP Bottom Bracket, BB-GXP-A1, SRAM. Gutter Seal Technology drastically improves sealing against the elements while reducing seal drag. Weve designed a fresh cup forging for a high-end l...
www.sram.com ..read more
Cruzbike Forum
1w ago
Any Cruzbike owners in the Scottish Borders/North Northumberland area?
I'm really interested in seeing an S40 and to talk to an owner about their experience with the bike ..read more
Cruzbike Forum
1w ago
Looking for a second fork. would like to experiment with the handlebar position.
Non-suspended fork (or one with suspension including the headset.).
thanks ..read more
Cruzbike Forum
1w ago
Does anyone know if compressionless brake housing will fit thru the internal routing access points on the S40? If not, would it be possible to safely enlarge the access holes ..read more
Cruzbike Forum
1w ago
Cruzbike Vendetta v20, selling one of my Cruzbikes to raise money for another bike project. This bike has mostly been on my trainer for the last couple of years. It was built from a frameset that I got and the chain stay, handlebars, top tube and bottom bracket shell were all purchased new from Cruzbike within the last two years. Included is the Ventisit pad and dual water bottle holder. It has SRAM Rival shifters/derailleurs. The crankset is 165mm cranks off of my v20c. I have an SRAM...
Read more ..read more
Cruzbike Forum
1w ago
I am installing SRAM Rival hydraulic brakes on my Q45 and I need to run the tube to the back wheel through the frame. The tube is small enough to go through the openings but I can't see how to get the tube out the exit. I tried in both directions. It looks impossible. Any ideas ..read more