Hi, the register muxenab=0x01, is this ok? i also tried to change it to 0x10 and it didn't help. Can you explain what the difference and if this can cause the issue? Thank you,   ..read more

I'm working with the CYW43012; The actual part is a Murata Type1LV chip. (1) Is it possible to change the  transmit power output duty cycle for 5GHz WiFi? If so, please explain how to do so? Is there an NVRAM setting that I can modify to change the duty cycle. I have viewed Infineon's AN225021 (see attachment) document and I do not see a corresponding NVRAM setting. (2) Also in the AN225021, there is an NVRAM setting called pa5ga0. Please explain what the example data for this settings consists of 12 values separated by comma. I'm guessing that the 12 values are actually 4 sets of 3 value ..read more

Hi @LH123,  The hardware is capable of LTE coex however the software for the same is not ready yet and we do not have the timelines for the same. You could contact the Infineon Sales/marketing team to for this feature.  Regards VIvek.  ..read more

Hi, I've been trying to get the GATT responses working (Read Requests mostly), but I seem to be having some issues. Here is the behavior that I am getting: when I send the response (either synchronously or asynchronously), I immediately get a second request for the same attribute. Synchronous: the function returns WICED_BT_GATT_SUCCESS in the GATT callback; Asynchronous: the function returns WICED_BT_GATT_PENDING. I have been looking through the documentation to understand what I am missing. I assume that it has something to do with the length of the payload (or offset), but I cannot find any ..read more

which pin of CYBLE343072 that i connect to pin 4  and pin 6 LCD to mcu spi mosi and sclk because from the datashet all i could find is pin 33 SPI_MISO ..read more

Hello,  You need to program the firmware first before run the code in debug mode. In MTB, you only need to enable debug by change the ENABLE_DEBUG?=0 to ENABLE_DEBUG?=1 in makefile Could you please check the message while build application for the CY_PLATFORM_SWDCK  and CY_PLATFORM_SWDIO ? For example : By default it will use P_02 as SWDCK and P_10 for SWDIO. If there is no defining pin for SWD then you need to add those flag at DEFINES in makefile,  for example :   DEFINE+= CY_PLATFORM_SWDCK=WICED_P28 CY_PLATFORM_SWDIO=WICED_P29​   by default SE ..read more

Hi @efio , COuld you please let us know if you are using  SDIO out-of-band interrupt or In bind interrupt. ? Regards Vivek ..read more

Hi, Please note using transmit power parameter, we can set  power from 0dBm to -28dBm or we can  select set the custom power setting specifying the either dbm or power table Index. Regards, Tushar   ..read more

Hi Phanindra_I , I've confirmed our evaluation board using Murata 2AE instead of STM32H747I-DISCO board with the Murata 2AE(CYW4373))(Actually Embedded Artist's M.2 module). The result is good and I can get the correct CISDUMP data. I wonder why the  STM32H747I-DISCO board with the Murata 2AE(CYW4373))(Actually Embedded Artist's M.2 module)  can not show the cisdump. I've debugging with STM32CubeIDE and dump the buf parameter area after the following function. result = cywifi_get_ioctl_buffer(cmd, (uint8_t *) buf, len); 02:00:00:00:00:00:00:00 00:00:00:00:00:00:00 ..read more

(5) Transmit Power: 0x09 (6) Transmit Power dBm: 0x00 (7) Transmit Power Table Index: 0x00   So setting Transmit Power to 0x09 is specifying to use the Transmit Power Table Index?  Please share the Transmit Power Table Index value. If I want to use the Transmit Power dBm, what should I set Transmit Power to?  Please give examples ..read more