Flooring Forum » Concrete Flooring
44 FOLLOWERS
This forum is an area for enthusiasts to talk about Concrete Flooring. Find help on striping the paint from painted concrete garage floor, and discover tips for drilling anchors here.
Flooring Forum » Concrete Flooring
1w ago
I measured a very nice large home on Friday. It's going to have a wide plank LVP throughout.
After drawing the layout, I went around with my 6' angle aluminum straight edge..... Oh dear
The slab has 1/4 inch wide saw cuts about 10 feet both directions. Some may have been separate pours. Where they meet, some edges have curled up a little or one side sunk a little bit.
The home is 36 by 75 and only 45' is concrete. Where the wood framing and concrete meet up, it's fine. The slab joints...
Read more ..read more
Flooring Forum » Concrete Flooring
3M ago
I have done a lot of research about concrete and how it's possible to finish it. I did a quick water droplet test and the concrete does not seem to absorb the water, the drops pool on the surface for a long time, maybe 20 minutes.
Specific questions:
- Would staining the concrete be an option (to avoid paint, which I've been warned about many times)? If so, do I need to etch the surface before staining it?
- If etching is necessary, what's the safest / simplest way to do it, since it's not...
Read more ..read more
Flooring Forum » Concrete Flooring
4M ago
Any idea why this new garage floor turned out like this and how it can be made to look similar to the rest of the floor? Concrete contractor said it was because the sun was blocked by the retaining wall during the curing process ..read more
Flooring Forum » Concrete Flooring
5M ago
I'm in the process of patching and skim coating the basement, and one of the pillars is sitting on a rock or something, and I'm trying to figure out if it would make sense to try patching and coating it using concrete, or if there are any extra concerns I should be considering ..read more
Flooring Forum » Concrete Flooring
5M ago
Hello everyone,
I'm reaching out for some expert advice regarding a unique issue with our new home's polished concrete floor. The floor has distinct black color, but there are visible swirls on the surface that are about 1 mm thick. I'm not sure what they are - possibly from a densifier or a top coat?
I'm considering sanding down these swirls and restoring the shine by progressively using diamond resin pads of increasing grit levels. However, I'm concerned about potentially altering the...
Read more ..read more
Flooring Forum » Concrete Flooring
9M ago
The concrete floors in my new house are so dusty. Every time I sweep so much brown dust is there. Any one know what is going on ..read more
Flooring Forum » Concrete Flooring
1y ago
Thanks for being a part of this community! To fund its operation, we have a Supporting Member program. It helps to ensure this community thrives for years to come.
Please consider investing in this community!
For more information please visit: Account upgrades ..read more
Flooring Forum » Concrete Flooring
1y ago
I'm trying to decide whether to redo a gypcrete floor underlayment completely or just repair what I can and go with it. We have a third floor condo that flooded, the living room floor now sags about two inches to the center. It was inspected and is structurally ok. The gypcrete that is currently laid down is intact but softer than it should be. To contract a company to come repour the entire floor, they want $5350. Or I could cut out the areas that are sagging the most and fill in the worst...
Read more ..read more
Flooring Forum » Concrete Flooring
1y ago
What should be done with this issue ? .....appx 40 year old apartment building, on grad, with signs of damage. Any advise would be appreciated.......mike ..read more
Flooring Forum » Concrete Flooring
1y ago
I am building a 1500 square foot pole barndominium as a shop and Mancave. the concrete floor will be fiberglass reinforced with sawed control joints. About 500 sqft I want a high polish, the remaining 1000 sqft will get a mild grind and densified&sealed surface to resist stains.
I want to rent the machines.
Can anyone recommend the size/ capacity of the grinding machine needed? Can anyone suggest a rental vendor that would send the machine(s) to Southern Illinois?
I will do all the grinding...
Read more ..read more