Hi! I'm using Logitech Mx Anywhere mouse and Mx Keys keyboard with a unifying receiver on linux with Solaar. Until very recently, this setup didn't pose any problem. However, since I temporary used the same receiver on a Mac, it makes troubles on my linux device. Whenever I wake up the computer from sleeping mode, both the mouse and the keyboard are blinking as if they were paired. Sometimes this takes several minutes until I can use the devices again. This is extremely annoying.. I don't know this behavior. Any idea what the problem is? submitted by /u/ghostly-matters [visit reddit] [commen ..read more

Recently I have been trying to connect my MX Keys Mini to a device whit no BT on boards. After some web search I ended up buing Logi Bolt reviver for the setup. Unfortunately, the host is not treating the Logi Bolt as a keyboard device, although couple of years a go I was using an older Unifying Reciever on it with a success. My question is are there any 3rd party revivers (other than the Logi Bolt one) wich could support the MX Keys Mini Keyboard? Best Regards, KM submitted by /u/Dzjadzic [visit reddit] [comments ..read more

Ordered a single item but got my order x10 (box is missing 2 cuz we’re using them) Guess whoever packed it didn’t care LOL submitted by /u/Bacon-80 [visit reddit] [comments ..read more

Bought a combo touch for my iPad Air and boy after 3 years does it look bad. Started tearing on the underside today to where it connects to the keyboard and it’s been sagging by the speaker holes since right after the warranty expired ?. And of course you can’t just get a new upper case and have to buy a whole new unit. submitted by /u/nqthomas [visit reddit] [comments ..read more

I assign the keystroke of a simple Tab to Button 4 and it only functions like Alt-Tab. Why does Set Point only allow weird pre-fab assignments anyway? I would like to have multi-key press assignments, but fixing the Tab problem is a priority. I really need to be able to change targets using the mouse buttons instead of moving my hand to the keyboard in Revit. Control Center version: 6.90.66 Driver version: 6.00.115 submitted by /u/nonaccnone [visit reddit] [comments ..read more

On Windows 11 device manager my MX Master 3S shows up as a generic device with a Microsoft driver. Do they even make a Windows driver anymore? I’m not talking about Options++, that’s an app, not a driver. Not having a specific problem other than wanting it to show correct hardware with actual Logitech driver. submitted by /u/Life-Ad1547 [visit reddit] [comments ..read more

I just got this mouse brand new and I love everything about it except the scrolling. Looked it up and a lot of other people seem to have the same issue as me, where if you scroll just a little bit or alternate between up and down it'll completely miss certain clicks. All that I've seen in terms of solutions is cleaning out the mouse with compressed air (it's new...) as well as disabling smart scrolling in Logi Options+, which I have disabled. This basically renders the mouse useless to me, as this is my method of scrolling after 20+ years and it makes games/editing nearly impossible to work w ..read more

I know it might be a silly question but I am buying the Mx Master 3s and Mx mechanical keys mini. Both come with a Logi bolt so i will have two Logi bolts in total. Can I use ONE logibolt to connect the mouse and keyboard to my main PC and the OTHER logibolt to connect the mouse and keyboard to my Work laptop. Then map the 1,2 device selectors to switch between Logi bolts on each device ? submitted by /u/Kashiawash [visit reddit] [comments ..read more

Love the mouse, but can we get a new revision where the mouse is not made with rubber (some kind of metal)? Mine was bought about 2 years ago, used it daily, and it's getting indented and sticky (where my thumb and few fingers rest). Come on Logitech! ​ Other related Reddit posts: https://www.reddit.com/r/logitech/comments/vcxmad/my_extreme_way_of_preventing_mx_master_33s_sticky/ https://www.reddit.com/r/logitech/comments/y47w97/replacing_the_rubber_coating_on_my_mx_master_3/ submitted by /u/neohanime [visit reddit] [comments ..read more

Hello all, My work recently purchased a Logitech Meetup for our conference room, and I've been tasked with getting this up and running. Is there a way to mirror the output video? Thanks in advance. submitted by /u/FloridaWaffleOG [visit reddit] [comments ..read more