Processor Boards • Re: MicroMod SAMD51 Dead
SparkFun Forums
by TS-Russell
4M ago
Stat shouldn't unless data is processing; though it should have a default blink sketch Here's the guide you're after https://learn.sparkfun.com/tutorials/mi ... e-overview Statistics: Posted by TS-Russell — Tue Jul 09, 2024 9:52 pm ..read more
Visit website
Designing With Artemis • Re: SparkFun Global Tracker Digikey Parts List
SparkFun Forums
by TS-Russell
4M ago
Grab Eagle and the parts are all in the brd file https://cdn.sparkfun.com/assets/3/2/c/a ... racker.zip (2 crystals, 32.768 kHz; 3.2 x 1.5mm) https://cdn.sparkfun.com/assets/f/4/5/3 ... IC_v10.pdf Has our functional schematic too Statistics: Posted by TS-Russell — Tue Jul 09, 2024 6:52 pm ..read more
Visit website
Designing With Artemis • SparkFun Global Tracker Digikey Parts List
SparkFun Forums
by sahmed
4M ago
Hi! I'm trying to design a smaller version of the SparkFun AGT and was wondering if there was a list somewhere of the parts used to populate the board (ex. the crystal oscillator used). Thanks! Statistics: Posted by sahmed — Tue Jul 09, 2024 2:22 pm ..read more
Visit website
Feedback On Everything Artemis • Re: Artemis resets time stamp evetime I power off and on the device while not connected to computer
SparkFun Forums
by PaulZC
4M ago
Hi picodots, The OLA RTC will reset if you remove the power without first putting the Artemis into deep sleep. Please see this section of the hookup guide - especially the section on "Stop Logging and Reset Buttons": https://learn.sparkfun.com/tutorials/op ... iderations I hope this helps, Paul Statistics: Posted by PaulZC — Sun Jul 07, 2024 8:48 am ..read more
Visit website
Feedback On Everything Artemis • Re: Artemis resets time stamp evetime I power off and on the device while not connected to computer
SparkFun Forums
by picodots
4M ago
Also having the same issue here. Every time when power is disconnected from the OLA, the RTC resets itself and I need to manually set the RTC time and date again. Is there any way to avoid this? Statistics: Posted by picodots — Sun Jul 07, 2024 1:15 am ..read more
Visit website
Processor Boards • Re: MicroMod SAMD51 Dead
SparkFun Forums
by user462744
4M ago
The stat LED does not illuminate on the processor board. The LEDs on the ATP do illuminate. Both products were purchased through Amazon. I'm hoping someone has a guide that explains how to go from a bare chip, installing the bootloader and any updates, through flashing a sketch. Statistics: Posted by user462744 — Thu Jul 04, 2024 6:34 pm ..read more
Visit website
Processor Boards • Re: MicroMod SAMD51 Dead
SparkFun Forums
by TS-Russell
4M ago
Are the LEDs lighting up on the processor or the ATP? Also see here https://learn.sparkfun.com/tutorials/mi ... r--drivers If it keeps giving issues: Was it purchased from us? If so head over to www.sparkfun.com/returns (contact vendor if purchased elsewhere) and we'll get ya squared away Statistics: Posted by TS-Russell — Thu Jul 04, 2024 4:48 pm ..read more
Visit website
Processor Boards • Re: MicroMod SAMD51 Dead
SparkFun Forums
by dboddie
4M ago
Sorry to hear that. I didn't make any progress with trying to revive mine. I had bought mine from DigiKey about two years before using it, and at least it worked for a few months before failing. Statistics: Posted by dboddie — Thu Jul 04, 2024 12:57 pm ..read more
Visit website
SparkFun Products Using The Artemis • Re: Board disconnects immediately over USB
SparkFun Forums
by PaulZC
4M ago
Hi edutchie, Many thanks for the update. It does sound like you have a faulty board - or at least intermittent contact on the USB connector. Please complete a return request and we'll replace the board for you: https://www.sparkfun.com/returns Apologies for the hassle, Paul Statistics: Posted by PaulZC — Thu Jul 04, 2024 8:42 am ..read more
Visit website
Processor Boards • Re: MicroMod SAMD51 Dead
SparkFun Forums
by user462744
4M ago
Sorry, that was a detail I meant to include. I also purchased the ATP main board. This is the first I've used the UF2 bootloader and just uploaded a sketch the old fashioned way through the Arduino IDE. Later I read about double pressing the reset enabling the board to be accessible like a thumb drive. Before I could upload a sketch using the drag and drop method, it stopped working. So long story short, no, it does not appear when I plug it into a PC. Statistics: Posted by user462744 — Thu Jul 04, 2024 12:39 am ..read more
Visit website

Follow SparkFun Forums on FeedSpot

Continue with Google
Continue with Apple
OR