Amateur Radio Emergency Data Network Forums
104 FOLLOWERS
Read the general discussion on Amateur Radio Emergency Data Network here. Share your thoughts, ask questions and get them answered by the experts.
Amateur Radio Emergency Data Network Forums
18h ago
Forums:
General discussion
How do i know what package is which and what each one of them does. when i set up one of the nodes it said if i want to block known encryption from going out over RF i need to install the package. Is there place that explains the package list and what they do? Is there any packages i really should be installing ..read more
Amateur Radio Emergency Data Network Forums
18h ago
Forums:
General discussion
Good Afternoon,
Though I'm not new to AREDN, we have now taken the deep-dive and have set up several nodes at various sites as well as a few that are based in residences. Some are RF...some are not; however, all have Internet access.
I'm trying to wrap my head around how access to specific nodes & services is done...especially to one's own nodes. Normally on a typical network, setting up shared access is pretty straightorward but my understanding of how AREDN approaches access and "sharing" is unclear.
Is there a guidance document that migh ..read more
Amateur Radio Emergency Data Network Forums
18h ago
Forums:
General discussion
Could someone tell me the settings for these 3 parameters with WinSCP?
Old and lost my notes...
File Protocol
Host name
port number
thanks...
Richard ko0ooo ..read more
Amateur Radio Emergency Data Network Forums
4d ago
Forums:
General discussion
I'm looking at the mikrotik series of antennas for my next purchase into my AREDN adventure. Namely the MikroTik SXTsq 5 ac. Does the AREDN firmware load like the HAP ac lite or is there other ways it needs to accomplished?
Any help is greatly appreciated.
  ..read more
Amateur Radio Emergency Data Network Forums
4d ago
Forums:
General discussion
Aloha
Is there a VM image, i currently have a hAP running and take the ports over to VLAN's on my network so i can pass the traffic to different repeater cabinets and the shack while keeping the hAP in the main network cabinet. I'm wasting 3 ports on my switch one for each VLAN and would like to use the hAP in the truck. Is it possible to load this up in VMware or virtualBox so i can use the hAP somewhere else? i figured it would be easier to add the VLANS in a VM to share my advertised services. i would assume someone on the develo ..read more
Amateur Radio Emergency Data Network Forums
6d ago
Forums:
General discussion
I have a Mikrotik hAP ac lite named hap-fb , and a Raspberry Pi named rp5b1 . I had MeshChat api 2.10 in hap-fb and apparently MeshChat 1.02 in rp5b1. A local group uses a MeshChat zone called NTX-Chat, and the rp5b1 was configured to do that.
Trying to get ready for AREDN 3.24.4.0, I deleted the MeshChat api app from hap-fb (the AREDN node) and installed MeshChat 2.12.0_all.ipk in it. Everything appeared to go OK.
When I looked at hap-fb Mesh Status, I saw two MeshChat zo ..read more
Amateur Radio Emergency Data Network Forums
1w ago
Forums:
General discussion
I've gone through pages of the Forum, Github and the new Troubleshooting pages, to hopefully find answers, so before I go through a reflash.
I have 2 Nodes setup with the following.
Firmware 3.23.12 on Node 1 and 2
Meshchat 2.12.0 installed on Node 1
Using a Windows PC, connected to the LAN port, with no errors during installation. Both nodes can see each other, both show Meshchat on the mesh status page under services, highlighted in red. I've tried numerus settings in Advertised Services,
From Installing MeshChat ..read more
Amateur Radio Emergency Data Network Forums
2w ago
Forums:
General discussion
Does anyone have the original software for the KKmoon or Yoluke cameras?
I am desperate for these and will pay for it, or I can copy your diskette.
Thanks!
Bob W8ERD ..read more
Amateur Radio Emergency Data Network Forums
1M ago
Forums:
General discussion
Hello everyone I have some questions and hopefully someone can answer them. I got my hands on some free equipment, a couple of MANTBOX 15s and a RB4011iGS+ I don't find software for the last one and I'd like to use it as a router since the ManTBOX only has one port. which leads to my second question... How do I set up the MANTBOX to connect to the internet or tunnels, It doesn't seem to conntect because it sees the only eth port as LAN port. I gave it an address in my local subnet but still wont connect to internet. Thank you all for the knowledge, I'm very n ..read more
Amateur Radio Emergency Data Network Forums
1M ago
Forums:
General discussion
Newbie here.
I installed meshchat on my hap lite router, and the setup page indicates that it was installed. What do I have to do to invoke or start it?
In a possibly related question the "mesh" box in the setup screen is unchecked for both my router and my LGH5 antenna. what does that mean? I do not seem to be able to change it and have it saved.
Thanks!
Greg Thumm
KK6YGX ..read more