2013 Brute 650 SRA The skid plate is missing and I can see what I think is a broken breather - part number 14069-1051. I think that's what it is anyway. Did some searching online to see what it does and if I should replace it but can't find much. Any ideas? I don't mind replacing it if it actually serves a good purpose ..read more

I bought a Lakota from a kid who jerry-rigged and mangled a bunch of stuff. I got the machine fairly cheap, and it does run and ride decent. But, it has its quirks. One of them being that he removed the starter solenoid and just stuck a switch on the side to jump the starter straight to the battery. Which works... but I would like to make it work as intended if possible. I started taking a look at the wiring and found a few connectors that are disconnected, and hoping someone might be able... Lakota, trying to identify some wiring ..read more

I was hoping for some advice on my Mule. I have a 2015 4010 Trans and it has always run very reliably for me. I had to take it to be serviced at a dealer because I needed something on the axle repaired but it sat at the dealer for 5 months before they fixed it. I received it back but it keeps stalling out every time I take my foot off the pedal. I am testing out the fuel lines/filter/pump because I figured it might have gotten gummed up after sitting for so long and I found the fuel... 2015 Mule 4010 Stalling At Idle after dealer service for 5 months ..read more

I have a 2006 brute force 750 that the previous owner had put a 840 big bore kit in. I recently "blew the motor" after taking it for a test drive after replacing a whole pile of suspension and steering parts. I've taken it apart to discover that I shattered one of the dual valve springs into a million pieces which caused damage to the head. I had always planned on tearing the motor apart to switch to a non cracked crankcase (which i already have as well as a gasket kit and a new head) but i... 06 840 big bore kit dual valve springs ..read more

With vforce John out who still builds clutchs for drag racers and about how much ..read more

http://putstuff.putfile.com/72446/5904743 ..read more

I have a Kawasaki Prairie 700 that I am slowly trying to get back running after letting it sit for a number of months. (see video link below) I can't figure out why gas is leaking from the bottom (which is why you see under the atv) and why the exhaust is glowing red as if it is about to melt. The white smoke I figure is burning water/moisture that is still stored in the gas tank I presume. I have drained the oil (which had a gas/oil mixture to it some how) and put new oil 10w-40 in it... KVF700 Gas Leak & Glowing Exhaust??? FIX ..read more

I apologize for joining and posting, but I need help, and I'm hoping this is the place to get it. Maybe a few of you started here the same way. Bought used. Discovered water pump was bad.. replaced it. Ran fine for months (I only drive the 3 acres I have and a mile on dirt roads up to my son's.) One day I was off to my son's, temp light came on. Rested it, red lighted again before I got there, and was pushing fluid out of reserve. Found a post about being airlocked. Doubted it, as... 2009 4010 KAF620R Recurrent Overheating Problem ..read more

Hey everyone! I'm new to the forum so bear with me, please. I have a 2018 Mule SX 4x4 XC Camo (KAF400L) and a couple weeks ago, I went out to start it and only got a lot of clicking when I turned the key. It has a new battery and it's fully charged. My first thought was that the starter solenoid was bad so I got a new one and put it on. This time, As soon as I reinstalled the battery and attached the battery ground to the frame, the starter immediately kicked in, without the key even being... 2018 Mule SX 4x4 XC Camo Starter Issues ..read more

Over the weekend, I took the first steps toward getting my Mule 4010 a little more off the ground. I'd say I've succeeded in raising the front by 3 or 4 inches, and am pleased with the results so far. I made a video detailing many aspects of the work. It starts with a 2 minute summary of the finished work, and then goes back to the details. I don't have much time to edit it, and so appreciate the patience of any viewers. Feel free to comment on what I've done. Al... 2017 Mule 4010 4x4 SE, 2" lift kit, new wheels, tires, and spacers - installation ..read more