Onefinity CNC Forum
253 FOLLOWERS
Read discussions on Onefinity CNC machines and products. Also, talk about accessories like touch probes, joystick, webcam, breakout board, wire extension, and more.
Onefinity CNC Forum
7h ago
(topic deleted by author)
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
10h ago
Hello
Brand new out of the box. Everything except spindle in attached as i dont have that yet. I wanted to try out the x y and z but cannot get the estop to release and turn yellow. F1 has all green top to bottom. I did look at masso controller and the error light is flashing. So anyhow can i not jog the machine without spindle installed?
Appreciate any help yall may have.
Rusty
3 posts - 2 participants
Read full topic ..read more
Onefinity CNC Forum
2d ago
My tools database is a mess and I’ve had it. I want to start a new node and copy in my bits and fix the numbering and finally … to address the material specific settings nightmare I created.
I have quite a few bits from different manufacturers and the specs from each, like freud and amana make their tool data downloadable.
Do you find that, for the most part, all 1/4" EMs are run at the same settings? Do I really have to care if it’s a Freud bit, an Amana, etc? I have some pricey (coated, etc.) bits that I could track separately, but are the general ones all the same? I’d love to eliminate the ..read more
Onefinity CNC Forum
2d ago
Trying to figure out many many circuits and what amperage I need for the journeyman pro. Will be running the machine a makita router, the touchscreen, and a shop vac. I’ve seen 2 20 amps is this correct?
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
2d ago
I have an elite and new to this. I have a cnc metal machine and when i tell the metal cnc to go to 0,0,0 on start up it goes and uses the sensors to do that. My elite seems to reset 0 on x and y axis. i have checked the settings and sensors and settings. I have updated the firmware to the latest version still errors. WHen i set up a job and after it runs it wants to reset 0 to the job zero not 0,0,0. Ideas?
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
2d ago
if you have interest to use wireless mpg work with beckoff ,please check this link:https://www.youtube.com/shorts/mPl47Pfa0uU
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
2d ago
I have looked everywhere but cannot find topic that answers my question. I have Journeyman machine due in May 2024 and have been working on design of my table and have question about power supply.
I am thinking of mounting it inside a section of the table. I plan on designing a push button on the front or top of the cabinet to turn supply on and off. If inside, will it need an external cooling fan or does it only require a minimum cubic area of free space.
Thanks
Ed
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
2d ago
Can anyone tell me what the Voltage and Watts output on the Onefinity/Masso power supply are.
1 post - 1 participant
Read full topic ..read more
Onefinity CNC Forum
3d ago
I’m 3D roughing a job in poplar and I noticed that it’s dust. The chip load was super low. I have a chip load range chart by material type, but I’m having a hard time believing it, because the only way I can seemingly get it in the range is by increasing the FPM beyond what I’d expect or by dropping the RPM below what I’d expect.
For instance, I had it at 80 FPM and 19k RPM.
If I plug in 100 FPM and 5k RPM I get .01, but 5k RPM? Can the be real?
Aspire, OF Elite with stiffy, .25 ball nose for this case.
Thoughts? Thanks!
3 posts - 3 participants
Read full topic ..read more
Onefinity CNC Forum
3d ago
Hi, I need to etch onto brass and was wondering if anybody has any etching spray recommendations. I have the Jtech 44watt laser. Thanks for any input.
1 post - 1 participant
Read full topic ..read more