Creality 3D Official Forum
310 FOLLOWERS
Creality 3D Official Forum is a place to share resources, series of 3D printers, firmware services, share how-to's, discuss troubleshooting, and much more.
Creality 3D Official Forum
8M ago
Hello to you all,
I have a question I can't seem to find the answer to. Putting relevel a bed gives answers to that but my question is "if i slice a 3d model then relevel the bed, do i need to reslice it or not"
I could print 2 things one after the other and both prints could sometimes be different.
Thank you for taking the time to read this.
DREA
  ..read more
Creality 3D Official Forum
10M ago
The Z home position is too high. I can get it at the right height by manually adjusting the Z position. How do I save that offset?
Peter
  ..read more
Creality 3D Official Forum
10M ago
I just got an Ender 5 Plus upgrading from an Ender 3. The prints are not starting. It says "heating" but the temp is hot for PLA.
Peter
  ..read more
Creality 3D Official Forum
1y ago
Hi! recently I replace the STM32F103 chip of the Creality V4.2.2 Ender 3 Pro board because y shorted when connect the BL Touch.
I have the new chip soldered in place, I have a cheap ST-LINK V2 clone but I'm not sure if I can flash the Ender-3 ProMarlin2.0.6HW4.2.2EuropeMultiLanguage.bin file with the STM32CubeProgrammer.
I need to take some care before flashing the original firmware?
Thanks ..read more
Creality 3D Official Forum
1y ago
I found and bought carborundum glass plate larger than my print bed. Can I cut it to desired size or will it shatter ..read more
Creality 3D Official Forum
1y ago
my cr 10s pro v2 came with a bl-touch smart 3.1 fitted from new just lately it has been doing some funny things so i decided to replace it the bl touch has the info on the back A7XQX PB2R1 i can not find a bl-touch on the internet with those letters on the back and when searching for a bl-touch for cr10s pro v2 i get no hits so can somebody tell me if a cr bl-touch will work with my unit
the firmware on my printer is ver 1.70.0 bl
Barry ..read more
Creality 3D Official Forum
1y ago
I have an Ender 3 pro that currently has a v4.2.2 motherboard. My nozzle temperature suddenly goes wildly up and down and the printer will not print. I have tried many suggestions to fix this issue but nothing worked so I ordered a new v4.2.7 motherboard from Creality. ( still waiting for it to arrive). In the meantime I am trying to create a new .bin file for it in VSCode but everything I try fails. I get all the way to the end but it fails because of a Code 1 error, and also it tells me that mega 2650 does not suit the v4.2.7 motherboard. I have tried every solution I can find on the interne ..read more
Creality 3D Official Forum
1y ago
Hi Folks,
When my Ender 3 starts to heat the hot end, either starting a print, or just doing a prepare, after about 40c a long tone sounds, and the unit reboots. From what I have read elsewhere, it sounds like this might be the thermistor?   ..read more
Creality 3D Official Forum
1y ago
In the process of rebuilding my Ender 3 and needing to temporarily pull each wire out of the board-side connector to my X-axis motor controller wire, I apparently messed up on putting it back together. I'm hoping I didn't do any permanent damage but the X-axis no longer moves. Apparently, there must be some crossed wires. Unfortunately, all of the wires are black, not color coded. I am hoping to correct this.
Does anyone know the pin-to-pin connections are at each end of a stepper wire? I'll have to use a continuity checker to correct the order. As I've been trying to research thi ..read more
Creality 3D Official Forum
1y ago
I need help. I have an Ender 3, Simplify 3D slicer.
I want to take this patch and convert it to a leather embossing tool. Please help, I do not know how to accomplish this task. Thank you in advance.
brucekramer07@gmail.com
ARNE-Patch.jpg ..read more