Someone, please give me a quick test print file in Zcode- don’t have the slicer, but repairing a printer. 2 posts - 2 participants Read full topic ..read more

Hı,I have a problem about measurement of printed parts.I need help for this issue.Measurement is so important for this part.When I was printing this part always measurement is different. You can see below pictures. Zortrax M300 Z suite 2.32.0 Z-Ultrat 2 posts - 1 participant Read full topic ..read more

Filament oozing refers to when excess melted filament leaks out of the hot end nozzle, often leaving small strings or blobs on the printed part. Oozing is caused by filament continuing to extrude from the nozzle even when it is not actively extruding plastic for the print. I ran into this little problem while printing with matte PLA. Share the solution. Firstly slow down printing speed, which gives filament more time to solidify. Ensure the hot end assembly is tight, wobble can exacerbate oozing issues. Printing at the lowest effective temperature for the filament can reduce oozing. Tuning ret ..read more

Hello, I had to buy external nylon(Taulman nylon 645) because Z-Nylon wasnt available and I have striging problems.I can’t go beyond 4mm for the the retraction but I still get stringing. I tried maximum fan settings hoping it would dry the oozing so it doesnt make strings but that doesnt work either. On auto I get the same result. The spool was new and I still go stringing. I will try to dry it see if it changes anything… So yeah, any suggestions what settings I could try to stop the strining ? Thanks for the help ! four_square_cons.zcodex2 (38.1 KB) 2 posts - 2 participants Read full topic ..read more

I used fusion360 to create the following When I tried to 3d print it using the Z-suite, the software restored the data on its own and I am having trouble. What should I do? syokusyo.stl (906.6 KB) 2 posts - 2 participants Read full topic ..read more

Hello Everyone, I’m thinking of making some wooden display stands out of plywood. These will be used to display. Something similar to https://customcraftltd.com/cnc-woodwork/ Can anyone give me ideas on the best design, type and thickness of material? Also would these be best glued or screwed together? Thanks in advance : ) 1 post - 1 participant Read full topic ..read more

Hi , I would like to use zortrax filaments in other machines then Zortrax… I have 5 differents printers and it is more easy for me to have only one brand. Where can I found the printing parameter of zortrax materials? Thanks 1 post - 1 participant Read full topic ..read more

I’m printing with Z-PETG on M300 printer, with external material settings. Prints are ok, nice walls surface. But when printing larger area top surface layer, it is wavy. I was trying with different settings - fan off or 20% or 80%. Also tried lowering density of top surface layers to 90%. Finaly I replaced new nozzle. But top layer always printed with waves. One layer before top seems ok, but then on top surface it makes waves. When I print object with smaller top area, there is no problem as can be seen on first picture chess piece in back of picture. Z-PETG spool is dryed. What should I try ..read more

Bonjour serait il possible de rajouter dans les paramètres un réglage pour le nombre de couches pour les paroies à la manière des dessus et dessous ? Merci cordialement 1 post - 1 participant Read full topic ..read more

@Saiko wrote: Hello, I would like some help. With each print the rear part of the perforated plate prints badly (see photo) I changed all these parts: extruder motor - nozzle and hotend - thermocouple - perforated plate - and the only part I didn’t have was the black extruder cable. So I changed to a black used extruder cable that I changed a few months ago. I did the calibration of the trays but the problem is still present. Do you have any ideas ? printing.jpg2016×1512 930 KB printing.jpg2016×1512 930 KB Posts: 3 Participants: 2 Read full topic ..read more