Cannot boot into OS if CPU clock ratio is set to 'auto'
Tech Support Forum » CPU
by adam.1
2d ago
Aside from undervolting the CPU, I have also capped its clock. If I change it back then it won't boot to either Windows or Arch... Any advice is very much appreciated. Motherboard - B450 Aorus M CPU - Ryzen 5 5500 ..read more
Visit website
Press F1 to boot after restart (920-fan command 2 pin connector from power supply not connected)
Tech Support Forum » CPU
by hor_mm
1w ago
setup: old HP d530 SFF(DK907A) Pentium4, running Fedora 8, power supply 500W HPQ-500BR-H12S, HP P6B580 motherboard (I will attach some photos as well) problem: I have to press F1 to boot after PC restart, and I need to make it independent from human interaction, because I am not always near that PC. The message is "920-Fan Command 2 Pin Connector from Power Supply Not Connected" Any ideas on what I could do so that I don't always have to press F1? thank you so much... press F1 to boot after restart (920-fan command 2 pin connector from power supply not connected ..read more
Visit website
Dual boot MB; 1 MBR, 1 GPT drives, GPT won't boot, same O/S
Tech Support Forum » CPU
by videobruce
2w ago
Specs; Gigabyte GA-970A-D3P Rev 2 older MB (2016) AMD based system. Main drive; 250GB SSD W7 Pro x64 MBR no hidden partitions Backup; brand new 4TB same O/S GPT one created System partition using Disk Part . Backup is seen in the Bios, but won't boot even if the SSD is disconnected. The MB is advertised as "dual boot". No custom settings, no overclocking etc. I've tried different Boot settings, the few that are there and no difference. The system always boot to the MBR. I haven't reset the... Dual boot MB; 1 MBR, 1 GPT drives, GPT won't boot, same O/S ..read more
Visit website
HP Pavilion 500-267 c
Tech Support Forum » CPU
by jetlagtoo
2w ago
Hello, not sure if I have this in the right place if not, please move to proper place. I haven’t been here in quite a while as things were running smoothly until about a week ago. I have an HP Pavilion 500–267c running windows seven. motherboard is: IPM87-MP or IPMB7- MP not sure if it’s an 8 or a B other numbers on the motherboard are: 706825-003 OPK. 732239-503 W8-8TD. 732239-503- 603-W8-PRO. Also 707825-003 About a week and a half ago I heard a loud banging noise coming from the computer... HP Pavilion 500-267 c ..read more
Visit website
System that worked fine for years suddenly refuses to boot with RAM set to XMP speeds
Tech Support Forum » CPU
by Cyber Akuma Zero
2w ago
I am pulling my hair out trying to solve this, I tried asking elsewhere but nobody could help. Here is my build: https://pcpartpicker.com/user/Cyber_Akuma/saved/vJypBm If you just want the important parts: CPU: 11700K Motherboard: Gigabyte Z490 Aorus Pro AX RAM: G.Skill Ripjaws V 64 GB (F4-3600C18D-64GVK) I have been basically building this system since early 2021, budget constraints have prevented me from fully finishing it but it's at least been in a functional state for a... System that worked fine for years suddenly refuses to boot with RAM set to XMP speeds ..read more
Visit website
MBR GPT Problem
Tech Support Forum » CPU
by sgeneris
3w ago
I have an older used Dell Latitude E7450 laptop on Windows 10 customized to my needs. It has a regular Bios and the disk is MBR, but it is UEFI capable. There are 3 partitions: C: system primary Extended partition: D: apps (logical drive) E: data (logical drive) I have acquired another E7450 w. Win10 to hold in reserve in case the current one fails, that I intend to keep in sync so that in any emergency I can switch immediately. The disk is GPT but in Bios the legacy boot is checked... MBR GPT Problem ..read more
Visit website
Gigabyte GA-MA790X-UD3P 5 long beeps one short
Tech Support Forum » CPU
by ReWinthech10
1M ago
so im building a retro pc (sorta for me its also a lil nostalgic cuz its my old mobo good memories like when i ripped out the plastic of a usb port) has that error code as stated in the title and i forgot what it emant im gonna try reseating the ram cause i remember it coud be possible the fualt and ill reply with how that went ..read more
Visit website
Motherboard lights
Tech Support Forum » CPU
by OscarMikeyy
1M ago
So i have these lights on my motherboard labeled cpu, vram, vga and boot 3 of these buttons light up in sequence when i try to start my pc Upon pressing the button the cpu light comes on and stays on until just before my fans spin to life Then once all the lights are on in the case the vga light comes on and stays that way for about 3 or 4 seconds then the boot light comes on and immediately turns off leaving my pc in a state of limbo where everything appears to be working but the monitors... Motherboard lights ..read more
Visit website
PC beeps 6 times and shows no display
Tech Support Forum » CPU
by gregorimontilla09
2M ago
Hello, So I have a PC I built; it has an i5-12400f and an RX 6750 XT with an ASRock B660M Pro Rs Motherboard. I used to have an RX 6600 before, but I recently upgraded. Now, after upgrading, I have been having issues. Every time I turn on the PC, it beeps 6 times at a normal cadence—not super fast or slow, just normal speed, 6 times.After the beeps, the display does not work and shows nothing; it takes me another boot for the pc to actually work and not beep or show no display. It has been... PC beeps 6 times and shows no display ..read more
Visit website
How to open a motherboard .cad file ?
Tech Support Forum » CPU
by sheawolgnds
2M ago
I received a .cad file for my laptop but don't know how to open it. Any suggestion ..read more
Visit website

Follow Tech Support Forum » CPU on FeedSpot

Continue with Google
Continue with Apple
OR