Brian Enos » Shotgun Technical
60 FOLLOWERS
Brian Enos provides chat rooms for shooting, tech, multi-gun, announcements, match management. This section is for discussing equipment, repair, issues, problems and much more.
Brian Enos » Shotgun Technical
1w ago
Hi guys,
i have bought a second M2 with loading port already opened. But after several month the factory's follower beginning to stuck after shooting the last shell.
I have tried to change the follower for one with a bigger diameter (Browning A5 's follower) but same problem again. Have you an idea to help me to fix it ?
Thanks by advance for your help ..read more
Brian Enos » Shotgun Technical
2M ago
Hi All,
I'm new to the site and to the VR82. Took it to trap shoot for the first time today. Result with the following:
25 shells Heuters 7 ½ 1200 fps (3 inch) - I had perfect performance with no failures of any kind. I found the sights to be highly accuate right out of the box. It could not have been better.
20 shells Winchester 7 ½ 1200 fps (2 ¾ inch) - The shells fired with no problems, but I had 100% failure to cycle the bolt far enough back to pickup the next shell in the magazine. I also had about 95% failure to eject the spent shell with mostl ..read more
Brian Enos » Shotgun Technical
2M ago
All,
I have a but of a unique problem.
I have a Farrow Tech RMR mount intended for pistol/micro dot mounting to shotguns (Beretta Comp Pro).
I have a Holosun 510C that i’d love to make work with this mounting solution.
Is there a way to adapt the 510C to the mount? Alternatively, I also have a Trijicon MRO that I could use instead.
trying to avoid going to a Pic rail as it sits taller than the mount and hinders a good cheek weld.
  ..read more
Brian Enos » Shotgun Technical
2M ago
My issue with y Breda is when I have 2 shells in the gun. The 1st is shot and ejected but the 2nd doesn’t get all the way in and jams the gun. It’s like the lifter is not putting the shell in the center of the barrel. Any help would be appreciated ..read more
Brian Enos » Shotgun Technical
2M ago
I've got a 1301 Comp Pro with a Nordic extension and Nordic barrel clamp. I've got it oriented correctly, and tightened as much as I dare to. But after a 5 stage match, it's always moved forward out of the groove on the extension tube, by about 1/8".
Is there a way to stop this, or am I stuck just re-positioning and re-tightening repeatedly?
Thanks,
Outbreak ..read more
Brian Enos » Shotgun Technical
4M ago
Hi Folks..I am in the UK and I am trying to find out if these guys still operate as i need to try and get something
for my Akdal MK1919 shipped over the pond.
Thanks for any help ..read more
Brian Enos » Shotgun Technical
5M ago
Are the hammer and trigger springs from a M2 interchangeable with the Nova/Super Nova? I’d like to use reduced power springs so if they aren’t interchangeable where’s a source for some? Another question, I’m sure some of you have played with the radius on the bottom of the bolt. Is there anything “slicker” or “more better” than just cleaning it up and polishing the cocking slot/hammer raceway? @kurtm ..read more
Brian Enos » Shotgun Technical
5M ago
Hi everyone,
I am trying to buy small parts in action tube assembly. Specifically parts #4 and #8
  ..read more
Brian Enos » Shotgun Technical
5M ago
All,
I've searched everything I can think of, so I apologize if this has been answered before.
I did mild loading port modifications to my SX2. The first match after putting it all together, I had 3 failures to feed, where the shell would just sit on the lifter, but the lifter would not lift. If I gave the lifter a push with my finger, the lifter would lift and the action would cycle.
I don't think that any of my modifications would have affected this. I broke the edges of the magazine tube junction, and did a pretty mild loading port opening job.
Could this be related to the lifter spring nee ..read more