Pirate 4x4 » 4Runner
88 FOLLOWERS
This section features forums on '79-'95 Truck and 4Runners. It also offers a discussion on wiring issues, different build issues, auto adapter, and much more. Pirate 4x4 forum is a community dedicated to custom off-road vehicle owners and enthusiasts.
Pirate 4x4 » 4Runner
2d ago
An early 22r block (w/ domed pistons) bored out +0.06 over with a 2.6l stroker kit. would this be too much compression or not enough clearance for a 20r head? what if? in this scenario I used the 22re flat top pistons would that lead to too low of compression? (I do still want to use 87 pump gas). - this is probly doing too much.
would a 22r stroker kit would work with a 20r block and pistons and head? - this would make a REALLY torqy engine.
are there any other cool builds you can do with...
Quick dumb question about a 20r/22r hybrid motor or any 20r build ideas ..read more
Pirate 4x4 » 4Runner
4d ago
1984 4Runner, 22r, 5 spd, with rear heat.
So I'm almost done with 100% desmog and had a question about hear hose. There is a small metal pieces that bolts to head between ports on the on the intake manifold and a metal hard hose that wraps around the rear of the block to a soft rubber hose. Can I delete this and just route the hose differently or? I haven't quite figured it out through research. All the heater re-routes are for newer 4runners and the pickups that don't have rear heat like...
Desmog/ heater hoses ..read more
Pirate 4x4 » 4Runner
3w ago
My new to me rig has 98,000 miles and I wanted to freshen up the suspension among other ware items. Over the weekend I busted ass installing new front springs, bushings,u-bolts and shocks on my clean ,stock 1985 Hilux xtra cab 4x4 .
I am not a expert but how the springs look just setting on flat ground looks f'd up. Shackles jammed up to the frame, I" bump stop clearance and the springs have a negative arch. Here are the photos...
[ATTACH...
new stock front replacement springs reversed curved and frame rides on shackle ..read more
Pirate 4x4 » 4Runner
1M ago
Starting my build and need some input. Looks like most Toys are using 1.75" tube for Exo work. I used 1.5" on my last build which was a Samurai buggy.
Think I can get away with 1.5" on a Toy ..read more
Pirate 4x4 » 4Runner
1M ago
I found a dent in my front axle while its apart so its time for armor. I had a piece of metal laying around and got to work. It took way too much effort to bend in the vice so I figured a way to bend it in my press. excuse the mess
put a small bend at each line to make a curve...
diff armor on the cheap ..read more
Pirate 4x4 » 4Runner
1M ago
I am swaping a 97 3.4 A/T out of a 4runner into an 90 3.0 M/T extra cab. I am going to use the 3.0 trans knowing the computer will throw codes for it. I'm ok with that. I bought a brand new 3.4 flywheel from napa. A 3.4 clutch assembly and am using a 3.0 throw out bearing like everyone says to use. After bolting the motor and trans together and trying to start it. The motor started to turn over then locked up. I pulled everything back apart to see what was wrong and it seems that my clutch...
3.0 to 3.4 Clutch problem ..read more
Pirate 4x4 » 4Runner
1M ago
My new to me rig has 98,000 miles and I wanted to freshen up the suspension among other ware items. Over the weekend I busted ass installing new front springs, bushings,u-bolts and shocks on my clean ,stock 1985 Hilux xtra cab 4x4 .
I am not a expert but how the springs look just setting on flat ground looks f'd up. Shackles jammed up to the frame, I" bump stop clearance and the springs have a negative arch. Here are the photos...
[ATTACH...
new stock replacement springs are reversed curved(less than flat) and shackles on the frame ..read more
Pirate 4x4 » 4Runner
1M ago
My 82 toyota truck 4x4 manual transmission has a loud whine on accel and decel in all gears but otherwise works well and shifts very smoothly. The noise sounds very much like a differential whine. I am wondering if a bad front input shaft bearing might cause this? The old truck is generally noisy enough that it is possible I am hearing the rear diff, but sure seems like it's coming from the trans. Ideas most welcome ..read more
Pirate 4x4 » 4Runner
1M ago
What size front driveshaft do I need for a 1983 Toyota 4x4 pickup with a Chevy 4.3 and 700r4 tranny with a 3-1/2” suspension lift. It’s a stock transfer case on a stock cross-member. The stock front driveshaft hit the tranny oil pan and so was never installed. And has since, gotten misplaced. I remember it was a double-cardan driveshaft though ..read more