Hi, I had to reinstall Windows and now I have a problem with CorelDraw2020. I can't start CM3. I always used CorelDraw X7 and had the same problem first. There was a sequence I had to follow what to install first, but I can't remember. Plotter Driver, CM3, Corel? Corel, CM3, Plotter Driver? I dont know. I testet all possibilities. I have testet CM4 also and there's the same problem. Starting CM3 alone is working. Windows 10 Pro 64bit 20H2 CorelDraw 2020 CM3 v2.2.1252gc Grapthec 5000-60 Driver: OPS662v300 ..read more

Hey!  Everything has been working just fine. Now, I get a message: Launcher cannot connect to Corel Draw .. any suggestions?   Corel Draw x7 - Graphtec CE6000    I would appreciate any input or suggestions.  ..read more

I’ve seen a few posts about this in other forums but never the solution.  I have a design page of 4”h X 24” wide and I have 2 rows of 28 decals I think that.  I go to export as eps, no matter what I chose in there as options it saves a 4x24 page but my decals are rotated 90° and only print in the middle like it was a standard 8.5x11 sheet.  I can open it in other programs and it shows exactly what is described above and what actually prints.  Any suggestions ..read more

This is about Illustrator.  But I put it here as it's more of a CorelDraw thing.  Draw defaults to a one handed mouse wheel zoom.  I have done this for years.  I set Inkscape to this behavior as well.  Illustrator can mouse wheel zoom, but you have to hold down alt.  This is such a tedious thing to adapt to mentally.  It is one of the prime reasons I don't fiddle in Illustrator.  On another post a guy said you could now set Illustrator to do this.  So I gave it a try.  Nope, still can't.  Some what undaunted, I began exploring.  I fou ..read more

hi, my issue iscoreldraw x8 does not show printer CE6000-60 grapthec when printing I have windows 10. I have installed the printer from disk ..read more

When I open up Corel, (see attached photo)  this is what I get, as soon as I left click it pops up, I'm stumped, don't know what to do ..read more

Trying to figure out how to add the black hard shadow like on this; Any ideas? Russ CT.eps ..read more

Anybody tried CorelDraw 2017 yet.  I am not sure how I feel about them going to what seems a yearly cycle vs the two year cycle they had been on.  I guess they want upgrade revenue.  It makes the subscription model more tenable if you are trying to stay current.   Most of the changes, though not all seem geared to people using some form or stylus for hand drawing.  They hype calls it an AI that learns your drawing style.  I am %99 mouse and keyboard.  I have a graphics tablet, but am all thumbs with it.  So I don't know if these improvements hit hom ..read more

Good Morning all.  Mom working on a small truck lettering job or a friend.  And for like life of my I cannot figure out how to do this in Corel draw.  What I need to do create a two color letter, gray lettering with a lime green "shadow"  ive attached what I am trying to do from a word doc.  I would like to have the shadow a little more pronounced  any input would help.  Thanks  ..read more

Hello, I am new to this forum as well as vinyl cutting in general, im hoping to find some help. Here is my current situation, im using a roland gx-400 and coreldraw x6.   Some of the problems I am experiencing, maybe due to my lack of experience.   I am having trouble cutting from corel draw, I have searched and seen some conflicting information on cutting from corel draw period ( is it possible) Provided this is possible, these are the steps I have been taking 1.     I create a simple image in corel draw, change it to wire frame, do the print preview, every ..read more