I got a bunch of Tulammo primers about 10 years ago. I broke into them recently and discovered my guns aren’t setting them all off. I hit the range today and out of 50, 14 wouldn’t go bang, in 2 different guns. If you had roughly 2k of these left, what would you do with them? To be fair, I haven’t tried them in my AR9, yet, since I discovered this recently. Perhaps that will have enough oomph. ETA of course these won’t be used in anything but range ammo, but I hate to put a bunch of time... What would you do with primers with a 28% failure rate ..read more

I ran a batch of 100 of these primers through 2 of my gen4 17's with no issues at all this morning. Both guns have stock internals/springs. I loaded them on a Dillon 650XL. I double pumped the downstroke when seating the primers, which is my normal SOP for whatever primers I may be loading. I think they're just a tad larger in diameter than say, Winchester SP's as it feels like they're being swaged down a bit as they enter and seat. They seated good enough obviously. Very small... Servicio Aventuras Small Pistol Primers Trial Run ..read more

Just started giving reloading a serious look, completely new to it. So far I'm looking at single stage lee presses, a reloading manual, calibers, scale. The two questions I have is 1. do I need a case trimmer if I'm only reloading 44 mag (Straight walled cartridge) 2. the only spot I'd have to reload is in the garage, which down south gets very humid especially during the summer, I'm assuming that could cause issues if the powders are exposed to that ..read more

I currently load the following 10mm load: 180 grain Xtreme plated HP CCI 350 primer 8.5 grains Longshot 1.26" OAL I can't find any loading data for a RNFP bullet. Any ideas ..read more

Ordered an 18" barrel and bolt from Mad Dog Weapon Systems about a year and a half ago along with Hornady Custom dies. Finally finished the build this year and today was my final test for load development with a 180gr Speer Hotcor. I am averaging out at 2615 fps with a SD of 4.7. This was my 4th reloading of this 20 pc test lot and I don't see why it couldn't take at least one more reload. Accuracy was 1.5" at 100 yards but I'm using a 3x Vortex scope. My eyes can't see much better than that... 358 Yeti (wildcat) 180gr Hotcor ..read more

Brassaddict.com seems to be not only legit, but great! 1000 rounds cleaned matching headstamp (WIN) brass for $55, no shipping, no tax, to my door today after an order two days ago!! NICE!! Two 500 round wrapped bricks nice & shiny ..read more

My G21 in 45 Super Load work up going great ! Using the Fed Nickle 45 ACP ( Not +P) Small Primer Pocket brass using Rem BR 7.5 Primers and 8.5 of PP with 250 FPRN getting 1065fps. No signs of pressure on case or primer. Glock 21 / 4.6” KKM and 22 pound recoil spring. Looks great case expansion still in the .470s. Max is .481” Never go back to 45 Super brass again ! Already exceeded 450 SMC Doubletap level. Titanium Firing Pin and 6 pound Wolff spring in G21. In 4.6” KKM. I also installed +4... 45 Super in Glock 21 ..read more

Great day at range today ! My 45 Super Load work up going great ! Using the Fed Nickle 45 ACP ( Not +P) Small Primer Pocket brass using Rem BR 7.5 Primers and 8.5 of PP with 250 FPRN getting 1065fps. No signs of pressure on case or primer. Glock 21 / 4.6” KKM and 22 pound spring. Looks great case expansion still in the .470s. Max is .481” Never go back to 45 Super brass again ! Already exceeded 450 SMC Doubletap level. Titanium Firing Pin and 6 pound Wolff spring in G21. In 4.6” KKM. I also... 45 Super Work up ..read more

I was kind of wondering why there is non-penetrator 62gr for sale ..read more

I'm looking for a good load for target shooting with the above bullet and powder. Shot from a P365. Anybody have a safe load I can just go with? Im not looking to do ladder test. I'm looking for reasonable accuracy at short distances. Ive never gotten an unsafe load off of GT for 9mm. Seriously looking for a load I can just load up 500 with and call it a day ..read more