TractorForum.com » John Deere
134 FOLLOWERS
A forum community dedicated to all tractor owners and enthusiasts. This section of the forum is a place to discuss John Deere Tractors.
TractorForum.com » John Deere
3d ago
I have a 2013 John Deere X540 with 48" deck. The serial number is in the 080400's. The PTO quit engaging this year. The battery is fairly new and checks good. So far I've replaced the switch, and the ECM and it's still doing the same weird thing. With the seat switch bypassed, parking brake off, Mower starts fine. When I push in the clutch and switch on the PTO I get no voltage on the blue PTO power wire. If I let off the clutch and switch on the PTO I get 15 volts coming into the wire...
X540 PTO not engaging, but has 15V to fuse box with switch and no clutch ..read more
TractorForum.com » John Deere
5d ago
Long story short - I bought and old 750 (with 3 cyl yanmar) that was sitting for years. I took head off and discovered that the rings were broken and had some corrosion in the cylinders. Since I knew nothing about this tractor transmission/hydraulics - I didnt want to dump a bunch of money into it so I just did a basic in frame rebuilt - honed cylinders, new rings/pistons and lapped valves.
It starts right up, runs ok and everything else seems to work. The problem is I have tons of...
John Deere 750 - Yanmar BLOW BY ..read more
TractorForum.com » John Deere
5d ago
Hi all! I'm new to this forum.
I have a JD5300 that is very loud when operating, even with ear protection on. I am trying to determine if the muffler is bad. Is there a way to check it? What should I expect for Decibel levels on this tractor with a good muffler ..read more
TractorForum.com » John Deere
2w ago
So I’ve got a 4052m that has a bad egr temperature sensor and I was wondering if I were to unplug the old one and just connect the new one will the code go away. Im wondering because I want to make sure that its actually the problem before I get into the repair ..read more
TractorForum.com » John Deere
1M ago
I just pulled my plow off my x324 John Deere tractor and installed the deck. I went to engage the blades and didn't get any response. The PTO won't engage. I'm about to start troubleshooting the tractor but I don't have any electrical diagrams. I don't know how many safety switches the tractor has other than the seat switch. Can someone tell me what other switches might affect the PTO and what's the best way to go about trouble shooting the system? Thanks ..read more
TractorForum.com » John Deere
1M ago
Trying to locate torques for 3T80J yanmar engine in a JD 850 tractor
Need connecting rods (rod caps) and head bolt torques.
Would appreciate any assistance.
Thanks ..read more
TractorForum.com » John Deere
1M ago
I was using my John Deere 950 the other day, moving machinery into my new shop, using the FEL and pallet forks on the 3 point hitch. I stopped for a water break , and when I came back, the 3 point does nothing, it will not lift at all.
I checked the fluid, it is full and still clean. I can see the linkage moving. Does anyone know if they can go bad and just stop working ? Any suggestions where I go from here to find the problem, I kinda need my 3 point attachments. TIA ..read more
TractorForum.com » John Deere
1M ago
Hello
Please i have JD 3520, year 2006.
I bought this used machine in not good conditon, but price is good
I want preventively calibration process for transmission, but when i make calibration procedure, calibration is not sucess and tractor is now wont move... I thing i have a bad method...
Please i need service manual for this tractor. And i need calibration procedure for transmission.
Please Anyone have that ..read more
TractorForum.com » John Deere
2M ago
Hey y’all. I purchased my father in laws house and have a few tractors on the property.
wanted to get some opinions on this one. Has an A sticker on the right front. Not sure what year it is. Looks like it’s been converted to an alternator.
any suggestions on getting it started ..read more
TractorForum.com » John Deere
2M ago
Last fall I was draining out the antifreeze and notice there was oil in the water when I drained the block. There was no water in the oil. The tractor runs fine. Doesn't smoke or miss. Does any one know what is going on ..read more