Hi guys! So I just bought a new pair of RAM from Kingston. The Kingston HyperX Fury RAM, 16GB 3200MHz. When I installed them and tried to use it on 3200MHz, my PC won't post. Instead, it works on the JEDEC standard 2666MHz only. Could it be that there is incompatibility between my PC components? And are there any ways to make this work? Any help or assistance is appreciated! My PC specs: Mobo: MSI A320M-A Pro Max CPU: Ryzen 3 3100 RAM: Kingston HyperX Fury 16GB 3200MHz (2x) GPU: Nvidia 1650 Super submitted by /u/AtlasVeroc [visit reddit] [comments ..read more

Pc specs: RTX 3060 12th 12900ks Corsair H100x elite liquid cooler 240mm AIO 32 gb ram So basically I have tried undervolting to around 0.065 and noticing good temp drops on a lot of games. For harder games I would still be in the 70s and I like it in the 60s. So I installed intel xtu and turned the p core ratio to 48x from 53x and now my temps are great and in the 60s even on hard games. So far not really any noticeable performance drops I am just wondering if this is bad for the cpu in any way and if it’s a bad ideas to do this? submitted by /u/Skiffyy85 [visit reddit] [comments ..read more

I recently bought asrock 5600xt challenger oc But my pc freezes while some games and Freezes exact at same frame in unheaven engine and times spy graphics test 1 Tried every method on internet but no help In games it randomly freeze stuck at wired rrrrrrrr sound No response in pc My spec Athlon 3000g B450m pro 4 Gskill 3200 8*2 3200mhz Cv450 80+ bronze submitted by /u/Mindless-Impress-360 [visit reddit] [comments ..read more

I've done everything I can to try and figure out why my pc will not stop hard locking itself. See the attached parts list. https://pcpartpicker.com/list/BY2CQP I've turned down all the Motherboard defualt settings. Processor Core ICC max: 307A Power max to 253 W. Turned XMP on and off nothing changed there. still does it. I have updated the MB bios, reinstalled every driver I can think of i've literally run out of things to do and check anybody have anyideas? It only crashes during gaming I can't play for longer than 10-20 minutes before the shit locks on me. It hasn't done it while sitting i ..read more

Hello guys I tried using the curve optimizer now the first time I got it to work all cores 5.1ghZ and -30 on curve optimizer. Right after I tried going to 5.15ghZ but that didn't work so I tried going back to 5.1 but then I had kernel not found or corrupted bsod. -5 on curve optimizer doesn't even work. Do you guys think it's bad drivers? submitted by /u/Shockwave_Baby [visit reddit] [comments ..read more

im thinking of getting a 6700xt or 7600xt or something like that, but i see in msi after burner you can extend oc'ing limits i plan to get a used one and repaste it then stretch my gpu to the max so that might be useful to other buyers and might sway a certain card for me submitted by /u/TheBronzeNecap [visit reddit] [comments ..read more

submitted by /u/Mother_Scarcity_2229 [visit reddit] [comments ..read more

submitted by /u/TheOneRebornReborn [visit reddit] [comments ..read more

Took off 0.01in from 0.17' ---> 0.16' off the copper heatsink. Now it weights 1gram less, and my temperature stays in the 25°C-28°C at idle and below 60°C at max gaming. Now I only need to install the Thermaltake CPU bracket to further improve the Temps. Boosts to 4.7Ghz, auto voltage. submitted by /u/Proper_Plantain_6925 [visit reddit] [comments ..read more

Recently bought a new gpu so it's time to oc my 13700k to keep up with it. It originally was auto OCed but ran too hot (90°C under load) so I undid the oc completely down to base speeds. I'm wanting to do a modest over clock to start with. I simply dont have the time with work and life to fiddle for hours on end so I was wondering if someone could give me some starting numbers for the bios settings that should be a safe starting bet for me to build on considering I've never done this. My current speed is 3.7ghz and the cpu runs at around 45-50° during gaming so there is plenty of thermal room ..read more