Modded Raptors Forum
3 FOLLOWERS
A forum community dedicated to Yamaha Raptor ATV owners and enthusiasts. Come join the discussion about troubleshooting, classifieds, performance, modifications, maintenance, and more! Share more about your favorite model including the: Yamaha Raptor 700, Raptor 660, Raptor 350, Raptor 250 as well as the smaller Raptor 50, 80 and 90.
Modded Raptors Forum
1w ago
hello i have a 2008 raptor 700r and its been sitting for about 8 months but i had it running last months im trying to take it to winchester in two days but i cant if it wont run i have a bad solenoid so i replaced it and i got a new battery so it cranks fine but still wont start i can here the pump running when you turn the key and i checked the plug and it was dry so i sprayed some starter fluid on the air filter and it started right away but instantly died it has spark and a charged new...
2008 yamaha raptor 700R se crank but no start ..read more
Modded Raptors Forum
2w ago
Raptor 660 11:1 piston bored to 686 stage 2 cam and dual looney tunes exhaust elevation 10feet above sea level ..read more
Modded Raptors Forum
3w ago
Hello all sry for my english im french
I'm desperately looking for someone who can make me a metal subframe
Thanks a lot ..read more
Modded Raptors Forum
1M ago
Ill kick it off. I only have one right now but ill get more up ..read more
Modded Raptors Forum
1M ago
I've built numerous dirt engines across almost all of the manufacturers, i've bought case sets for replacment but never a half… Are the OE castings that accurate to buy just one half of a crankcase? Center case half, not a side or cover. Have a TRX450R here that needs hours of cleanup just to repair.. would rather buy a half if it is a good idea.
Anyone have some experience here? Obviously engine serial numbers do not matter to the owner.
Thank you ..read more
Modded Raptors Forum
2M ago
What you see is what you get. No engine. 1000 cash on low ball. Serious buyers only ..read more
Modded Raptors Forum
2M ago
Yamaha Raptor 660 valves adjustment
Tools you need:
10MM socket
17MM socket
19MM socket
Ratchet
Breaker Bar (optional)
3" Extension (not shown)
4MM Hex Key
5MM Hex Key
10MM Key
Needle Nose Pliers
Yamaha Spark plug socket (not shown)
Feeler Gauges
Philip Screw Driver (or socket like on the picture)
Service Manual for Torque Specs and Valves Clearance
AND A STONE COLD ENGINE...
Step-By-Step Valve Adjustment for Raptor 660 ..read more
Modded Raptors Forum
2M ago
Hello,
I am installing a 660 Raptor front end on my golf cart, and am missing some measurements because I don’t have a Raptor to measure from. Can someone please tell me what the measurements are from the front shock mount on the lower a-arm, to the upper shock mount on the frame with the ATV under normal weight? Also, if you could provide the shock angle, that would be greatly appreciated.
Thank you in advance. I’m anxious to hear your feedback ..read more
Modded Raptors Forum
2M ago
So I just did some upgrades on my 2020 raptor 700r se...105mm big bore kit...stage 2 hot cam...ported and polished cylinder head alba exhaust and fuel customs intake with stacker filter without the box....tuned with the dyno jet power commander tunner....I know they run at about 45 hp stock. Mine will hit the dyno on monday....any ideas what I should expect hp wise with my set up ..read more
Modded Raptors Forum
3M ago
I have a Racer’s Edge Gen 2 head for a raptor 700 for sale. It has +2 valves, KW springs and is set up for a 54mm TB. I am including a Web 290 cam and the machined rocker as well. I am returning my quad to stock to sell; as I no longer have people to ride with anymore. The head has a dyno tune and about 15min ride time on it. What I will include with the head is dependent on what you provide with your core. I am looking to get $825 + a good clean core for it.
I would be willing to sell...
RE Gen 2 Head/ web 290 cam ..read more