There are not many Magnas and Veradas around any more. Today, on the freeway at Gerringong(near Kiama) heading north towards Sydney I spotted a VERY tidy KH Verada in Kashmir(light beige). It looked to be in superb condition. Does that belong to anyone participating here? Anytime you see a fellow Magna or Verada, give them a wave, and post here ..read more

Hi Everyone, I'm new here. I had a question about the rear bumper. I have a 2011 Lancer Sportsback ES. I got rear-ended a while ago. I need to replace the rear bumper, but this has proven a bit of a challenge. I know my sportsback is built on the body of the lancer. Does this mean I can use a sedan bumper without issue ..read more

I just recently got my 2022 Mitsubishi Outlander SEL. I took delivery of this vehicle from another state so I did not get to see in person until it was delivered. The car is used and does have 45,000mi. The driver door is driving me crazy with a consistent creak noise when opening and closing. All other doors have a nice solid thunk. I tried using WD-40 on all the hinges and it is still creaking. Anyone run into this issue? I cannot see anything wrong with the hinges... drives me crazy for... Creaky Driver Door ..read more

I'm having an issue with the red airbag light on my dashboard that won't turn off on my Mitsubishi Space Star 2013. Recently, I removed the front seat to replace the clogged heating register in the coupe. The job is done, but after reinstalling the driver's seat, the airbag light stays on continuously. I've checked the wiring under the driver's seat, plugged and unplugged the yellow wire, lubricated the connections with WD40, followed a specific ignition sequence, used a cheap diagnostic... Airbag Light Issue After Driver's Seat Removal/Reinstallation ..read more

Hi, I have a Mitsubishi Space Star 2013 (1,2L 80HK) I've been dealing with a persistent issue of coolant loss, and I constantly have to refill it. I discovered a leak in the lower radiator hose clamp, so I bought a new worm drive hose clamp and installed it. Initially, it seemed fine, but it's started leaking again. I've tightened it so much that I suspect the hose itself might be leaking now. I recall that when I removed the "original" clamp, which was completely rusted, some of the rust... Radiator Hose Leakage ..read more

I'm trying to locate the immobiliser module in 2015 outlander ...is it the ignition or a separate module ? If so where is it located under the dash ..read more

If my etacs not pull out when i turn on the ign the wiper front and back is automatically on...and the A/T ign and funnel fuse will busted...all of the lights power window are not working ..read more

Hello everybody! Does anyone have a complete electrical schematic diagram for the Mitsubishi Endeavor. Please share it. I searched the entire Internet, found only a Mitsubishi Galant 9G ..read more

Hello, Anybody has this Mitsubishi Endeavor 2004-2007 Factory Service Repair Manual? I found this on internet for 10.99 us, http://www.tradebit.com/filedetail.php/107...e-repair-manual NO SHIPPING COSt, FREE DOWNLOAD!!! cover: 2004-2005-2006-2007 Mitsubishi Endeavor. You are buying a 2004-2007 Mitsubishi Endeavor Factory Service Workshop Manual. This is the very... Endeavor Service Manual ..read more

I’ve recently acquired a 10/92 Galant LS which by vin states I’d have 4g63 SOHC Vehicle came with new timing set and water pump and was already partly torn into. I’ve removed the belt and pulleys and found that my old belt is 124 tooth and the new belt is 123. I called up Mitsu and ordered the factory belt by vin and as it turns out it’s also 123 tooth. Is it possible that I’ve got a 2.4 swap as the 4g64 is all that comes up for the 124 tooth belt in my searching. I am missing the front... 123 vs 124 timing belt ..read more