My Tractor Forum
259 FOLLOWERS
Welcome to the friendly forum dedicated to all Tractor owners and enthusiasts. From specification to modification discuss everything you wanted to know about your tractor. Talk about lawn & garden tractors, BMWs, compact utility tractors, full-size tractors, accessories, and more.
My Tractor Forum
6m ago
I have a 14g with 501 hours on the clock just wondering a fair list price for this machine I know what it cost new and expect never to see that has hydraulic lift deck,has blower attachment wheel weights and chains it's also hydrostatic 4 high gears 4 low gears have original owner manual along with pink slip when purchased new along with dealer warranty card
...
How to value gravely 14g ..read more
My Tractor Forum
6m ago
The AM143388 Double Pulley has two diameters. OD1 is about 5.19". OD2 is about 5.48 " To my less than
eagle eyes, ii looks like OD2 pulley drives the blades and OD1 is driven by the engine, as shown in the JD
parts diagram. When I looked at mine, it looked like the smaller diameter pulley was driving the blades.
Is this how it should be? The X570 mows OK, I'm just asking to see if the factory might have had a new pulley
placement tech, the day mine was made ..read more
My Tractor Forum
6m ago
I have a brand spanking new Briggs and Stratton 23 hp V-twin Vangard engine and it was pining away for a tractor to power. So I went looking around and took a fancy to a '67 Jim Dandy which smoked like a bug sprayer and I thought needed an engine. Perfect. Right. Well close. Besides the output shaft being 1" diameter, it is an inch shorter as measured from the mounting surface where the "bell housing" meets the engine block to the tip of the shaft.
The question is: Does anyone know if there...
My engine needed a tractor ..read more
My Tractor Forum
3h ago
I have a sears suberban tractor and by belt is destroyed it is a 1966 sears 12hp engine and a 12 speed ..read more
My Tractor Forum
3h ago
Hi, I’ve got an old Gravely zero turn mower and I’m trying to find the hydraulic fluid. This is the only thing I can find. Everything that I found online doesn’t match anything that’s on my mower. Does anyone know if this on the left is where the hydraulic fluid goes? It’s has a dipstick, and the oil dipstick is on the right as you can see. That’s the only place I could find ..read more
My Tractor Forum
3h ago
Hello, everyone. My first time posting here.
I have a 2018 Simplicity Broadmoor 2691467-01.
I need to replace the flat connector from the wiring harness that plugs into the PTO clutch. It has a black and orange wire and a diode that jumps between them.
Simplicity wants to sell me a new wiring harness for $500. I found aftermarket splice repair kits online, but they're missing the diode. Anybody know what diode I'd need to buy? I can't tell from the diode what kind it is and Simplicity's...
Simplicity Broadmoor question ..read more
My Tractor Forum
3h ago
I have a John Deere Z225 ztrak residential mower. After about 25 minutes of run time the left arm doesnt want to engage, if I push both arms forward to go straight, just the right engages so I turn left. If I cut the mower off for about 3 or 4 minutes and start it back up the left arm will work for about 30 to 45 seconds and go back out. Anybody had a similar issue or know the fix? Thank you ..read more
My Tractor Forum
3h ago
Can someone help me on how to remove the plastic tire rims from my 12PT? (4 wheels). The plastic rims allow a slow leak of air and I want to put tubes in the tires. I contacted MacKissic but little help there. I know that I will need to replace the device that holds the rims onto the axle. This model does not use the cotter pins that hold the rim onto the axle.
Thanks in advance,
Mark Anderson ..read more
My Tractor Forum
3h ago
Hello. I’ve enjoyed reading about the old Gravely lawn tractors on this forum. I’m
wondering if someone can help me find a repairman. My last guy retired. I’ve called around the area, and I’m told the shop doesn’t work on the old ones anymore.
I have the old 8123 (not a zero turn, I get asked that a lot).
I think I have a couple issues going on, but I’d even love it if I could help with the seasonal maintenance. I’m not too familiar but I don’t want to muddle around and make anything...
Gravely 8123 - how to find a repairman ..read more
My Tractor Forum
7h ago
Hey, all.
Every time I engage the PTO on my 99 345 it makes a loud squealing noise as it engages. The noise lasts about a second and then stops as the deck comes up to speed.
My PTO did die on me not long ago and I've replaced it, so it is new, and I had hoped that maybe that would stop the noise, but it is still there just like before.
I picked up this tractor about a year ago and it's been doing it since I bought it, so I don't know if this is normal - but, I assume it is not.
Is...
345 w/54" deck - Squeal when engaging PTO ..read more