Modded Mustangs
353 FOLLOWERS
A forum community dedicated to all Ford Mustang owners and enthusiasts to discuss about racing, builds, modifications, troubleshooting, maintenance, performance and so on.
Modded Mustangs
13h ago
I’m at a loss and looking for some insight or ideas on what could be causing this issue. Here’s the low down.
Car puffs out white smoke when left to idol for a few minutes. None of the smoke that accumulates during idol comes out, until I hit the gas.
No smoke when driving. I’ve been told the smoke is blue, I’ve been told the smoke is white. I’ve been told it’s the piston rings by several people but I’m not convinced due to testing. When smoking, I do get water droplets coming out of...
Car smoking while left to idol ..read more
Modded Mustangs
13h ago
'00 GT AODE 317K miles (daily driver) and going strong, bought my Stang brand new. I've maintained the car properly, it is not abused.
How much on average cost to have the oil pan gasket replaced done by a shop? I've read and watched how time consuming it looks by DIYs. I don't have the experience to do this pm on my car.
Also, would it be worth it if I have the shop replace the OEM k-member with an aftermarket tubular or similar to make my car lighter? with an aftermarket replacement...
oil pan gasket ..read more
Modded Mustangs
22h ago
l have a 66 with an I/6 and a complete World Class T-5 system. I lost use of my lower legs and am looking for a good automatic system for trade. My I--6 is heavily built so it would have to be a complete c-4 set up. Anyone interested ..read more
Modded Mustangs
2d ago
I have a 96 3.8 mustang i have a major issue. when i first start it up she runs ok for about a mile or so. also it takes longer to start but at times she cranks right up. but after the first mile is starts to miss and it will not pull at full throttle. it will bog down but wont stall out. it is annoying. i can run on the hight way around 2000- 2400 rpm and she runs ok pulls but as soon as i press the pedal down she boggs down. it also miss fires #2 cylinder. i have Full exhaust no cats...
96 3.8 Mustang No Power Full Throttle ..read more
Modded Mustangs
3d ago
Before everyone starts laughing....has Ford made the 99-04 FRPP Intake Manifold (aluminum crossover) obsolete? I went to a Ford dealership today and the parts person smirked when I mentioned the year '00 while he searched thru the database of parts. He said Ford made it obsolete. Anyone can confirm this? IF they are obsolete, guess I have no choice but to get the aftermarket replacement.
I've searched online for the IM because mine needs replacing (slow coolant leak in the Thermostat...
99-04 GT intake manifold ..read more
Modded Mustangs
3d ago
list your exhaust vid/sound clip and tell your setup and anything that would alter the sound of the exhaust that u have installed.
Please no discussion here. This is just for posting videos and descriptions.
MWWarlord said:
Ok guys it seems like everyday we get people asking about exhaust. You asked for it so here it is. The following is intended to be an unbiased review of exhaust options for the 3.8L V6 mustang. If anyone has any questions that are not answered in...
Click to expand...
OFFICIAL V6 EXHAUST THREAD with CLIPS ..read more
Modded Mustangs
3d ago
I have a 67 Mustang that I have converted to a Mustang two front end with rack and pinion. Was needing help on what power steering pump to use and steering column to use and headers. I want to have a tilt steering wheel column, power steering, air conditioning With a 302 and automatic transmission ..read more
Modded Mustangs
5d ago
I just purchased long tube headers for my 2020 Mustang gt. Would I need a tune as soon as I put them on or can I get a tune later and still drive it ..read more
Modded Mustangs
6d ago
I feel like it’s getting heat soaked fast and down on a lot of power. I was looking at an Afro dual pass heat exchanger but is it worth the 800 plus? Over a mishimoto universal with fans mounted? And the stock expansion tank if in the engine bay I was thinking about relocating. Would I need a pump if I ran it to the trunk ..read more
Modded Mustangs
6d ago
I have a Kenne bell 2.8 LC mammoth
8 rib conversion with tool and 3.0/3.5 pulley (16/21 psi)
6 rib kit comes with with a 9 psi pulley
Cobra jet TB
Fabbed adapter plate for the throttle body/and the one to fit the stock TB
Dual AFCO heat exchanger
Roush heat exchanger reservoir as the KB one sucked
Plug and play wiring kit
install instructions
I will let this complete setup go for 6200 shipped obo
ID 1000's are 725 shipped
less then 5000 miles on this stuff.
I am also parting out the car...
Kenne Bell 2.8LC mammoth, ID 1000s FS ..read more