MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
544 FOLLOWERS
No matter if you're a car-savvy DIY type looking to install a remote starter or looking to replace a worn out remote, we have tech's just a call away to help.
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
11M ago
To test to see if your 2007 Super Duty came with factory remote keyless entry, get into the truck, close the door, keeping your foot off the brake, first press the power unlock switch on the driver's door, then begin with the ignition OFF, turn the ignition ON (do not start the vehicle) and OFF 8 times within 10 seconds, ending with the ignition ON on the 8th time...if the vehicle was equipped with factory remote keyless entry, the vehicle's power door locks will respond automatically by cycling from unlock to lock. Now, turn the ignition OFF and order some new remotes: Call MotorCityRemo ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
11M ago
To test to see if your 2007 Super Duty came with factory remote keyless entry, get into the truck, close the door, keeping your foot off the brake, first press the power unlock switch on the driver's door, then begin with the ignition OFF, turn the ignition ON (do not start the vehicle) and OFF 8 times within 10 seconds, ending with the ignition ON on the 8th time...if the vehicle was equipped with factory remote keyless entry, the vehicle's power door locks will respond automatically by cycling from unlock to lock. Now, turn the ignition OFF and order some new remotes: Call MotorCityRemo ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
1y ago
Posted by: Derek AT 06:19 am | "Older 5 button Prestige and Pursuit model remote (example remote models: and 08SPR) not working properly after programming it to the system. After a successful programming procedure, only the LOCK button on the remote works. The UNLOCK and the remote start buttons don't do anything. And if I press the LOCK button 2 times, it will also UNLOCK the doors." With the older higher-end Prestige and Pursuit systems, the newer standard Prestige and Pursuit remote programming procedure where you turn the ignition ON, press the ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
1y ago
I have a CAT1LR Code Alarm in this Altima I just bought, the car ran good then my boy messed with the button when I drove it later it was sluggish and really felt like I was taking off in 5th gear. Is this an issue as far as protection? I'm really confused and just want to disable it if so. I need help plz." The Code Alarm system CAT1LR does not have the ability to cause the problems you report having with your vehicle. The button on the system's remotes can only activate the remote starter or shut down the remote starter when it's running by the remote starter... So ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
1y ago
How to Reset my Flashlogic FLRS Series Remote Starter System?" STEP 4: After the release of the button, the LED should turn on solid RED for a few seconds then turn OFF: Module reset is now complete: Next, you must reprogram the module to the vehicle following the vehicle-specific programming procedure which differs from vehicle to vehicle. Only the reset procedure is the same no matter what year, make, and model the vehicle is. , you MUST unplug the BLACK 20-PIN plug LAST ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
1y ago
With most automotive remotes yes, it can be replaced. You just need to provide us with the FCC ID off the back of the remote with the number of buttons on the remote, or, what brand and model of the system you have installed in your vehicle, and we can assist you with what exact replacement remote you need. For phone assistance, you can call our "Tech-Direct" support line at 1-586-315-4005 M-F: 9am-7pm, Sat: 9am-5pm, and Sun: 9am-3pm, Eastern Time ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
2y ago
Posted by: Derek AT 08:00 am | "I just bought a used vehicle with a Code Alarm CAT1 remote starter in it. I would like to know if there's a timer for how long the vehicle will stay started. Will the vehicle turn off after a certain amount of time or remain running until I enter the vehicle"? No matter what brand or model of a remote starter system, all remote starters will automatically shut off if the vehicle is not entered within a specific amount of time...the common run time is 15 minutes. Some may run longer (or even shorter), but all of them will automaticall ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
2y ago
Posted by: Derek AT 03:32 pm | "My Code Alarm 2-way remote will only lock and unlock my doors...and the screen on the remote keeps displaying "Zzz" on it...I think this means "sleep mode"...but I don't know how to take it out of this mode? Try: turn your ignition ON (do not start the vehicle), look up at the systems' antenna (which is probably mounted at the top center of the windshield on the glass behind the rearview mirror)...see if the LED light that is built into the antenna lights up solid when you turn the ignition ON (not flashing)...if it is, press an ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
2y ago
Posted by: D. Weber AT 08:00 pm | "I'm installing a remote starter system and I have 2 wires from the system that indicate main ignition 1 and ignition 2 and I'm finding 2 wires in the ignition harness that show power when the ignition is turned on, are these the ignition wires I need to connect to and which one is the main ignition and which is the 2nd?" A "main" ignition wire (or a.k.a. "true" ignition wire) is always the wire that shows NO +12VDC power as soon as you probe the wire with the ignition OFF, and then it immediately shows +12VDC power ..read more
MotorCity Remotes | DIY Remote Starter Kits, Replacement Remotes & Accessories
2y ago
Posted by: Derek AT 06:19 am | "Older 5 button Prestige and Pursuit model remote (example remote models: and 08SPR) not working properly after programming it to the system. After a successful programming procedure, only the LOCK button on the remote works. The UNLOCK and the remote start buttons don't do anything. And if I press the LOCK button 2 times, it will also UNLOCK the doors." With the older higher-end Prestige and Pursuit systems, the newer standard Prestige and Pursuit remote programming procedure where you turn the ignition ON, press the ..read more