If you have locked the keys in your car, no need to panic quite yet. If you vehicle has a locking tab mechanism that slides up and down, usually by the window, you can unlock it using nothing but a shoelace. Step 1: You will want to remove the shoelaces off of a pair of shoes. You will need two. Step 2: Tie the two shoelaces together by tying a double knot and the end of each lace. Step 3: Form a loop about 3/4 of the way down the string and tie another double knot. Step 4: Starting at the top corner of the door jamb with the long side of the string towards the front of the car, slide your la ..read more

Slide Key Into Ignition: Without starting the vehicle, turn the vehicle on to ACC mode. Enter Programming Mode – Step 1: Press the “i” button on the dash twice Enter Programming Mode – Step 2: Once you see “Program Remotes” on the instrument cluster, click the check button below the “i”. Program Remote: Once the display says “PUSH FOB”, PRESS and HOLD the LOCK and UNLOCK buttons together. When your hear the car chime, the vehicle has successfully entered the new remote/fob. Program Additional Remotes: Follow step 4 to program any additional remotes including existing ones. Test Remotes: Once ..read more

https://youtu.be/D0mHsXxPutg Have you locked the keys inside of your Dodge Avenger? This is a how to unlock 2009 Dodge Avenger with no keys when you are locked out. Professional technique and instruction video for unlocking a Dodge Avenger using lockout tools. Step 1: Slide your airbag into the door jam. Start at the top of the door and slide it up and down. Begin pumping until you see a big enough crack to slide in a tool. Step 2: Use your long reach tool to hook the door handle. Step 3: Deflate your airbag to avoid risk of damaging vehicle. Step 4: Grab your key ..read more

Have you locked the keys inside of your GMC Sierra? This is a how to unlock 2005 GMC Sierra with no keys when you are locked out. Professional technique and instruction video for unlocking a GMC Sierra using lockout tools. Step 1: Slide your airbag into the door jam. Start at the top of the door and slide it up and down. Begin pumping until you see a big enough crack to slide in a tool. Step 2: Use your long reach tool to flip the manual lock paddle to the unlocked position. Step 3: Deflate your airbag to avoid risk of damaging vehicle. Step 4: Grab your keys and your’re good to go ..read more

Installation and User Guide Prepare the door and check dimensions If drilling a new door, use the supplied template and the complete door drilling instructions available at www.weiserlock.com/doorprep Measure to confirm that the hole in the door is either 2-1/8″ (54 mm) or 1-1/2″ (38 mm). Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm). Measure to confirm that the hole in the door edge is 1″ (25 mm). Measure to confirm that the door is either 1-3/8″ or 1-3/4″ (35 mm or 44 mm) thick. Note: Additional door preparation may be required for doors with 1-1/2 ..read more

Installation Instructions Schlage Keyless Touchscreen Lever [FE695] Keyless Touchscreen Lever Prepare for Installation Tools Needed Phillips screwdriver, #1 and #2 bits Tape Measure Pencil Optional Flathead Screwdriver Wood Block Hammer IMPORTANT NOTES DO NOT use a power drill for installation! Install and test lock with door open to avoid being locked out. A Check door dimensions. See consumer.schlage.com/Service-Support for door preparation instructions if dimensions are different. B Change faceplate, if necessary. Choose the drawing that matches your door edge. If the hole has no ..read more

How to Figure Out Which Lishi Tools to Buy First? If you are just starting to get into automotive locksmithing, lishi tools are going to be a very useful tool you need to purchase. They can be expensive and there is so many to choose from. When I started off, I could not reason the cost of buying every single one, especially because some hardly get used. The way I made my decision was I went to the busy mall parking lot and took a tally of almost 200 cars. I then refined my recordings to which lishi tools I would need for each. This gave me an idea of what lishis would be most useful in my ar ..read more

Light Tension Be sure to follow this guide to properly prepare your lock for a lishi tool. After your lock is prepped and your tool is inserted into the lock, the lishi tool is fairly easy to learn. First you want to take your left hand and apply light tension on the tension handle. Many people when starting off will use what I call Gorilla Hands and apply way too much force. In some cases, an increase of tension can be strategically used but in general keep the tension light. Tension should be applied throughout the whole procedure. If you let off tension, the wafers will reset and you will ..read more

Why Should You Clean Lock Before Lishi Picking? It is necessary to clean the a lock before inserting your lishi tool for a couple reasons. The first being that it is much harder on your lishi tool causing more wear and tear if you attempt to pick a dirty lock. The picking tips are very thin and can break easily. Knowing this, you will want to start by spraying a lubricant cleaner into the lock to limit the amount of dirt and dust particles in the lock. This will allow your picking tip to move freely throughout the lock with little resistance. Take a non oil based lubricant and aim the straw d ..read more

The numbers on keys can mean a couple different things and it is important your are familiar with these. In some cases the numbers are a way to identify which key blank you have. But in a lot of cases the 5-6 digit number can be the DNA to your key. Why is it important that you know what this code means? Many people (especially young people) will post pictures to social media of the keys to their new/first apartment or house. They are caught up in the excitement and likely not thinking about the security vulnerabilities with doing so. If someone sees the picture of their key and the code that ..read more